Datasheet
www.ti.com
ELECTRICAL CHARACTERISTICS: REFERENCE
ELECTRICAL CHARACTERISTICS: GENERAL
INA206
INA207
INA208
SBOS360E – JUNE 2006 – REVISED OCTOBER 2007
Boldface limits apply over the specified temperature range, T
A
= – 40 ° C to +125 ° C.
At T
A
= +25 ° C, V
S
= +12V, V
IN+
= 12V, V
SENSE
= 100mV, R
L
= 10k Ω to GND, R
PULL-UP
= 5.1k Ω each connected from
CMP1 OUT and CMP2 OUT to V
S
, unless otherwise noted.
INA206, INA207, INA208
REFERENCE PARAMETERS TEST CONDITIONS MIN TYP MAX UNIT
REFERENCE VOLTAGE
1.2V
REFOUT
Output Voltage 1.188 1.2 1.212 V
Reference Drift dV
OUT
/dT T
A
= – 40 ° C to +85 ° C 40 100 ppm/ ° C
0.6V
REF
Output Voltage 0.6 V
(Pins 3 and 6 of 14-pin packages only)
Reference Drift dV
OUT
/dT T
A
= – 40 ° C to +85 ° C 40 100 ppm/ ° C
LOAD REGULATION dV
OUT
/dI
LOAD
Sourcing 0mA < I
SOURCE
< 0.5mA 0.4 2 mV/mA
Sinking 0mA < I
SINK
< 0.5mA 0.4 mV/mA
LOAD CURRENT I
LOAD
1 mA
LINE REGULATION dV
OUT
/dV
S
2.7V < V
S
< 18V 30 μ V/V
CAPACITIVE LOAD
Reference Output Max. Capacitive Load No Sustained Oscillations 10 nF
OUTPUT IMPEDANCE
Pins 3 and 6 of 14-Pin Packages Only 10 k Ω
Boldface limits apply over the specified temperature range, T
A
= – 40 ° C to +125 ° C.
At T
A
= +25 ° C, V
S
= +12V, V
IN+
= 12V, V
SENSE
= 100mV, R
L
= 10k Ω to GND, R
PULL-UP
= 5.1k Ω each connected from
CMP1 OUT and CMP2 OUT to V
S
, and CMP1 IN+ = 1V and CMP2 IN – = GND, unless otherwise noted.
INA206, INA207, INA208
GENERAL PARAMETERS TEST CONDITIONS MIN TYP MAX UNIT
POWER SUPPLY
Operating Power Supply V
S
+2.7 +18 V
Quiescent Current I
Q
V
OUT
= 2V 1.8 2.2 mA
over Temperature V
SENSE
= 0mV 2.8 mA
Comparator Power-On Reset Threshold
(1)
1.5 V
TEMPERATURE
Specified Temperature Range – 40 +125 ° C
Operating Temperature Range – 55 +150 ° C
Storage Temperature Range – 65 +150 ° C
Thermal Resistance θ
JA
MSOP-10 Surface-Mount 200 ° C/W
SO-14, TSSOP-14 Surface-Mount 150 ° C/W
(1) The INA206, INA207, and INA208 are designed to power-up with the comparator in a defined reset state as long as CMP1 RESET is
open or grounded. The comparator will be in reset as long as the power supply is below the voltage shown here. The comparator will
assume a state based on the comparator input above this supply voltage. If CMP1 RESET is high at power-up, the comparator output
comes up high and requires a reset to assume a low state, if appropriate.
6 Submit Documentation Feedback Copyright © 2006 – 2007, Texas Instruments Incorporated
Product Folder Link(s): INA206 INA207 INA208