Datasheet

DS99R105, DS99R106
www.ti.com SNLS242D –MARCH 2007–REVISED APRIL 2013
DS99R105 Serializer Pin Descriptions
Pin
Pin Name I/O Description
No.
LVCMOS PARALLEL INTERFACE PINS
4-1, DIN[23:0] LVCMOS_I Transmitter Parallel Interface Data Inputs Pins. Tie LOW if unused, do not float.
48-44,
41-32,
29-25
10 TCLK LVCMOS_I Transmitter Parallel Interface Clock Input Pin. Strobe edge set by TRFB configuration pin.
CONTROL AND CONFIGURATION PINS
9 TPWDNB LVCMOS_I Transmitter Power Down Bar
TPWDNB = H; Transmitter is Enabled and ON
TPWDNB = L; Transmitter is in power down mode (Sleep), LVDS Driver DOUT (+/-) Outputs are
in TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption.
18 DEN LVCMOS_I Transmitter Data Enable
DEN = H; LVDS Driver Outputs are Enabled (ON).
DEN = L; LVDS Driver Outputs are Disabled (OFF), Transmitter LVDS Driver DOUT (+/-) Outputs
are in TRI-STATE, PLL still operational and locked to TCLK.
23 PRE LVCMOS_I PRE-emphasis select pin.
PRE = L; Pre-emphasis is enabled
PRE = H; Pre-emphasis is disabled
11 TRFB LVCMOS_I Transmitter Clock Edge Select Pin
TRFB = H; Parallel Interface Data is strobed on the Rising Clock Edge
TRFB = L; Parallel Interface Data is strobed on the Falling Clock Edge
12 VODSEL LVCMOS_I VOD Level Select
VODSEL = L; LVDS Driver Output is ±400 mV (R
L
= 100Ω)
VODSEL = H; LVDS Driver Output is ±750 mV (R
L
= 100Ω)
For normal applications, set this pin LOW. For long cable applications where a larger VOD is
required, set this pin HIGH.
5 DCAOFF LVCMOS_I RESERVED – This pin MUST be tied LOW.
8 DCBOFF LVCMOS_I RESERVED – This pin MUST be tied LOW.
13 RESRVD LVCMOS_I RESERVED – This pin MUST be tied LOW.
LVDS SERIAL INTERFACE PINS
20 DOUT+ LVDS_O Transmitter LVDS True (+) Output. This output is intended to be loaded with a 100 ohm load to
the DOUT+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
19 DOUT− LVDS_O Transmitter LVDS Inverted (-) Output This output is intended to be loaded with a 100 ohm load to
the DOUT- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
POWER / GROUND PINS
22 VDDDR VDD Analog Voltage Supply, LVDS Output Power
21 VSSDR GND Analog Ground, LVDS Output Ground
16 VDDPT0 VDD Analog Voltage supply, VCO Power
17 VSSPT0 GND Analog Ground, VCO Ground
14 VDDPT1 VDD Analog Voltage supply, PLL Power
15 VSSPT1 GND Analog Ground, PLL Ground
30 VDDT VDD Digital Voltage supply, Tx Serializer Power
31 VSST GND Digital Ground, Tx Serializer Ground
7 VDDL VDD Digital Voltage supply, Tx Logic Power
6 VSSL GND Digital Ground, Tx Logic Ground
42 VDDIT VDD Digital Voltage supply, Tx Input Power
43 VSSIT GND Digital Ground, Tx Input Ground
24 VSS GND ESD Ground
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: DS99R105 DS99R106