Datasheet

DS90C365A
www.ti.com SNLS181I –APRIL 2004–REVISED APRIL 2013
Electrical Characteristics
(1)
(continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol Parameter Conditions Min Typ
(2)
Max Unit
TRANSMITTER SUPPLY CURRENT
ICCTW Transmitter Supply Current, R
L
= 100Ω, f = 25MHz 29 40 mA
Worst Case C
L
= 5 pF,
f = 40 MHz 34 45 mA
Worst Case Pattern
f = 65 MHz 42 55 mA
(Figure 1, Figure 3 )
"Typ" values are given
f = 87.5 MHz 48 60 mA
for V
CC
= 3.6V and T
A
= +25°C, " Max " values
are given for V
CC
=
3.6V and T
A
= −10°C
ICCTG Transmitter Supply Current, R
L
= 100Ω, f = 25 MHz 28 40 mA
16 Grayscale C
L
= 5 pF,
f = 40 MHz 32 45 mA
16 Grayscale Pattern
f = 65 MHz 39 50 mA
(Figure 2, Figure 3 )
"Typ" values are given
f = 87.5 MHz 44 56 mA
for V
CC
= 3.6V and T
A
= +25°C, " Max " values
are given for V
CC
=
3.6V and T
A
= −10°C
ICCTZ Transmitter Supply Current, Power Down = Low, 11 150 μA
Power Down Driver Outputs in TRI-STATE
®
under
Power Down Mode
Recommended Transmitter Input Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol Parameter Min Typ Max Unit
TCIT TxCLK IN Transition Time (Figure 5) 1.0 6.0 ns
TCIP TxCLK IN Period (Figure 6) 11.76 T 50 ns
TCIH TxCLK IN High Time (Figure 6) 0.35T 0.5T 0.65T ns
TCIL TxCLK IN Low Time (Figure 6) 0.35T 0.5T 0.65T ns
TXIT TxIN , and /PD pin Transition Time 1.5 6.0 ns
TXPD Minimum pulse width for PWR DOWN pin signal 1 us
Transmitter Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol Parameter Min Typ Max Unit
LLHT LVDS Low-to-High Transition Time (Figure 4) 0.75 1.4 ns
LHLT LVDS High-to-Low Transition Time (Figure 4) 0.75 1.4 ns
TPPos0 Transmitter Output Pulse Position (Figure 12)
(1)
f = 25MHz −0.45 0 +0.45 ns
TPPos1 Transmitter Output Pulse Position 5.26 5.71 6.16 ns
TPPos2 Transmitter Output Pulse Position 10.98 11.43 11.88 ns
TPPos3 Transmitter Output Pulse Position 16.69 17.14 17.59 ns
TPPos4 Transmitter Output Pulse Position 22.41 22.86 23.31 ns
TPPos5 Transmitter Output Pulse Position 28.12 28.57 29.02 ns
TPPos6 Transmitter Output Pulse Position 33.84 34.29 34.74 ns
(1) The Minimum and Maximum Limits are based on statistical analysis of the device performance over process, voltage, and temperature
ranges. This parameter is functionality tested only on Automatic Test Equipment (ATE).
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS90C365A