Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPMIC - ELCs High side DIP 16

DS3658

www.ti.com

SNLS365B –MARCH 1995–REVISED APRIL 2013

DS3658 Quad High Current Peripheral Driver

Check for Samples: DS3658

FEATURES

DESCRIPTION

The DS3658 quad peripheral driver is designed for

• Single Saturated Transistor Outputs

those applications where low operating power, high

• Low Standby Power, 10 mW Typical

breakdown voltage, high output current and low

• High Impedance TTL Compatible Inputs

output ON voltage are required. A unique input circuit

combines TTL compatibility with high impedance. In

• Outputs May Be Tied Together for Increased

fact, its extreme low input current allows it to be

Current Capacity

driven directly by a CMOS device.

• High Output Current

The outputs are capable of sinking 600 mA each and

– 600 mA Per Output

offer a 70V breakdown. However, for inductive loads

– 2.4A Per Package

the output should be clamped to 35V or less to avoid

• No Output Latch-up at 35V

latch-up during turn off (inductive fly back

protection—refer to AN-213 'SNOA610'). An on-chip

• Low Output ON Voltage (350 mV typ @ 600

clamp diode capable of handling 800 mA is provided

mA)

at each output for this purpose. In addition, the

• High Breakdown Voltage (70V)

DS3658 incorporates circuitry that specifies glitch-

• Open Collector Outputs

free power up or down operation and a fail-safe

feature which puts the output in a high impedance

• Output Clamp Diodes for Inductive Fly Back

state when the input is open.

Protection

The PDIP package is specifically constructed to allow

• NPN Inputs for Minimal Input Currents (1 µA

increased power dissipation over conventional

Typical)

packages. The four ground pins are directly

• Low Operating Power

connected to the device chip with a special cooper

• Standard 5V Power Supply

lead frame. When the quad driver is soldered into a

PC board, the power rating of the device improves

• Power Up/Down Protection

significantly.

• Fail Safe Operation

• 2W Power Package

• Pin-for-Pin Compatible with SN75437

APPLICATIONS

• Relay Drivers

• Lamp Drivers

• Solenoid Drivers

• Hammer Drivers

• Stepping Motor Drivers

• Triac Drivers

• LED Drivers

• High Current, High Voltage Drivers

• Level Translators

• Fiber Optic LED Drivers

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (9 pages)

PAGE 1
DS3658 www.ti.com SNLS365B – MARCH 1995 – REVISED APRIL 2013 DS3658 Quad High Current Peripheral Driver Check for Samples: DS3658 FEATURES DESCRIPTION • • • • The DS3658 quad peripheral driver is designed for those applications where low operating power, high breakdown voltage, high output current and low output ON voltage are required. A unique input circuit combines TTL compatibility with high impedance. In fact, its extreme low input current allows it to be driven directly by a CMOS device.
PAGE 2
DS3658 SNLS365B – MARCH 1995 – REVISED APRIL 2013 www.ti.com Connection Diagram Figure 1. PDIP- Top View See Package Number NFG0016E These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage 7V Input Voltage 15V Output Voltage 70V Output Current Continuous Power Dissipation @ 25°C Free-Air 1.
PAGE 3
DS3658 www.ti.com SNLS365B – MARCH 1995 – REVISED APRIL 2013 Electrical Characteristics (1) (2) Symbol Parameter Conditions VIH Input High Voltage VIL Input Low Voltage IIH Input High Current VIN = 5.25V, VCC = 5.25V IIL Input Low Current VIN = 0.4V VIK Input Clamp Voltage VOL Output Low Voltage Min Typ Max Units 2.0 V 0.8 V 1.0 1.0 µA ±10 µA II = −12 mA −0.8 −1.5 V IL = 300 mA 0.2 0.4 V IL = 600 mA (3) 0.35 0.7 V 100 µA 1.
PAGE 4
DS3658 SNLS365B – MARCH 1995 – REVISED APRIL 2013 www.ti.com AC Test Circuit Figure 2. Switching Waveforms Figure 3. Typical Applications Figure 4. Stepping Motor Driver 4 Submit Documentation Feedback Figure 5.
PAGE 5
DS3658 www.ti.com SNLS365B – MARCH 1995 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision A (April 2013) to Revision B • Page Changed layout of National Data Sheet to TI format ............................................................................................................
PAGE 6
PACKAGE OPTION ADDENDUM www.ti.
PAGE 7
PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
PAGE 8
MECHANICAL DATA NFG0016E N0016E N16E (Rev G) www.ti.
PAGE 9
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.