Datasheet

DF1704
2
SBAS099A
PIN NAME I/O DESCRIPTION
1 DIN IN Serial Audio Data Input
(3)
2 BCKIN IN Bit Clock Input for Serial Audio Data
(3)
3I
2
S IN Input Audio Data Format Selection
(2, 4)
4 IW0 IN Input Audio Data Word Selection
(2, 4)
5 IW1 IN Input Audio Data Word Selection
(2, 4)
6 XTI IN Oscillator Input/External Clock Input
7 XTO OUT Oscillator Output
8V
SS
— Digital Ground
9 CLKO OUT Buffered System Clock Output
10 MODE IN Mode Control Selection (H: Software, L: Hardware)
(1)
11 MD/CKO IN Control Data Input/Clock Output Frequency
Select
(1, 5)
12 MC/LRIP IN Control Data Clock/Polarity of LRCK Select
(1, 5)
13 ML/RESV IN Control Data Latch/Reserved
(1, 5)
14 RST IN Reset. When this pin is LOW, the digital filter
is held in reset.
(1)
15 MUTE IN Mute Control
(1, 4)
16 DEM IN De-Emphasis Control
(2, 4)
17 SF0 IN Sampling Rate Select for De-emphasis
(2, 4)
18 SF1 IN Sampling Rate Select for De-emphasis
(2, 4)
19 OW0 IN Output Audio Data Word and Format Select
(2, 4)
20 OW1 IN Output Audio Data Word and Format Select
(2, 4)
21 NC — No Connection
22 V
DD
— Digital Power, +5V
23 DOR OUT Rch, Serial Audio Data Output
24 DOL OUT Lch, Serial Audio Data Output
25 WCKO OUT Word Clock for Serial Audio Data Output
26 BCKO OUT Bit Clock for Serial Audio Data Output
27 SRO IN Filter Response Select
(2, 4)
28 LRCIN IN L/R Clock Input (f
S
) for Serial Audio Data
(3)
NOTES: (1) Pins 10-15; Schmitt-Trigger input with pull-up resistor. (2) Pins
3-5, 16-20, 27; Schmitt-Trigger input with pull-down resister. (3) Pins 1, 2,
28; Schmitt-Trigger input. (4) Pins 3-5, 15-20, 27; these pins are invalid
when MODE (pin 10) is HIGH. (5) Pins 11-13; these pins have different
functions corresponding to MODE (pin 10), (HIGH/LOW).
PIN ASSIGNMENTSPIN CONFIGURATION
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
Supply Voltage (V
DD
, V
CC
1, V
CC
2R, V
CC
2L) .................................... +6.5V
Supply Voltage Differences................................................................. ±0.1
GND Voltage Differences.................................................................. ±0.1V
Digital Input Voltage ................................................. –0.3V to (V
DD
+ 0.3V)
Input Current (any pins except power supplies) ............................. ±10mA
Power Dissipation .......................................................................... 300mW
Operating Temperature Range ......................................... –25°C to +85°C
Storage Temperature ...................................................... –55°C to +125°C
Lead Temperature (soldering, 5s)................................................. +260°C
Package Temperature (reflow, 10s) .............................................. +235°C
ABSOLUTE MAXIMUM RATINGS
DIN
BCKIN
I
2
S
IW0
IW1
XTI
XTO
V
SS
CLKO
MODE
MD/CKO
MC/LRIP
ML/RESV
RST
LRCIN
SRO
BCKO
WCKO
DOL
DOR
V
DD
NC
OW1
OW0
SF1
SF0
DEM
MUTE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
DF1704E
NC: No Connection
TOP VIEW SSOP
PACKAGE SPECIFIED
DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT
PRODUCT PACKAGE NUMBER RANGE MARKING NUMBER MEDIA
DF1704E SSOP-28 324 –25°C to +85°C DF1704E DF1704E Rails
PACKAGE/ORDERING INFORMATION