Datasheet

Bill of Materials www.ti.com
5 Bill of Materials
Table 7. Parts Lists
(1)
Item # QTY Designator Manufacturer Part Number Description
1 1 C1 TDK C1608C0G1H101J 100 pF, 0603, C0G, 50V, 5% Tol, Multilayer Ceramic
Capacitor
2 3 C2 C3 C4 TDK C3216Y5V1C106Z 10 μF, 1206, Y5V, 10V, 10% Tol, Multilayer Ceramic
Capacitor
3 4 C5 C7 C10 TDK C2012X7R1E104K 0.1 μF, 0805, X7R, 50V, 10% Tol, Multilayer Ceramic
C11 Capacitor
4 3 C6 C8 C13 TDK C2012X7R1E104K Not Installed
5 1 C9 TDK C2012X5R1A225M 2.2 μF, 0805, Y5V, 10V, 10% Tol, Multilayer Ceramic
Capacitor SMD
6 1 C15 TDK C2012X7R1E474M 0.47 μF, 0805, Ceramic, Y5V, 10V, 10% Tol,
Multilayer Ceramic Capacitor
7 1 J1 J2 (top Samtec TSM-110-01-T-DV-P 10 Pin, Dual Row, SMT Header (20 Pos.)
side)
8 1 J1B J2B Samtec SSW-110-22-F-D-VS-K 10 Pin, Dual Row, SMT Socket (20 Pos.)
(bottom side)
9 1 J3 (top side) Samtec TSM-105-01-T-DV-P 5 Pin, Dual Row, SMT Header (10 Pos.)
10 2 J3B (bottom Samtec SSW-105-22-F-D-VS-K 5 Pin, Dual Row, SMT socket (10 Pos.)
side)
11 1 R1 Yageo 9C06031A1000JLHFT 100 Ω, 0603, 5%, 0.1 W resistor
America
12 1 R2 W2 W4 Yageo 9C06031A0R00JLHFT 0 Ω, 0805, 5%, 0.1 W resistor
America
13 1 R3 R4 R7 Not Installed
14 2 R5 Yageo 9C06031A33R0JLHFT 33 Ω, 0603, 5%, 0.1 W resistor
America
15 2 R6 Yageo 9C06031A1002JLHFT 10 kΩ, 0603, 5%, 0.1 W resistor
America
16 1 SW1 E Switch EG2209 DPDT Slide Switch
17 1 TP2 Keystone 5001 Red Test Point Loop
18 5 DGND AGND Keystone 5000 Black Test Point Loop
19 2 U1 Texas OPA735AIDBVT OPA735
Instruments
20 1 U2 Texas OPA735AIDBVT Not Installed – Optional Component
Instruments
21 3 U3 Texas DAC8831ICRGY 16-Bit, Unbuffered Voltage Output, Reset to
Instruments Zero-Scale DAC
DAC8832ICRGY 16-Bit, Unbuffered Voltage Output, Reset to
Mid-Scale DAC
22 3 U4 Texas OPA353NA OPA353
Instruments
23 1 U5 Texas REF3025AIDBZT REF3025
Instruments
24 1 W1 W3 Samtec TSW-103-07-L-S 3 Pin, Single Row, TH Header
NOTE:
(1)
P2, P4, and P6 parts are not shown in the schematic diagram. All the P designated parts are installed on the bottom side of the
PCB opposite the J designated counterpart. For example, J2 is installed on the topside while P2 is installed on the bottom side
opposite of J2. The following parts are not installed: J1, J3, R1, R2, and R3 .
18
DAC8831/32 Evaluation Module SLAU202A–December 2006–Revised November 2009
Submit Documentation Feedback
Copyright © 2006–2009, Texas Instruments Incorporated