Datasheet

Bill of Materials
2-11
PCB Design and Performance
2.3 Bill of Materials
Table 2-1.Parts List
Item #
Qty
Designator Manufacturer Part Number Description
1 2 C9 C10 Panasonic ECUV1H105JCH 1 µF, 1206 Multilayer ceramic
capacitor
2 4 C1 C2 C3 C7 Panasonic ECJ3VB1C104K 0.1 µF, 1206 Multilayer ceramic
capacitor
3 1 C12 Panasonic ECUV1H102JCH 1 nF, 1206 Multilayer ceramic
capacitor
4 3 C5 C6 C11 Kemet C1210C106K8PAC 10 µF, 1210 Multilayer ceramic
X5R capacitor
5 17 R8 R17 R25 R26
R27 R28 R29 R30
R31 R32 R33 R34
R35 R36 R37 R38
R39
Panasonic ERJ-8GEY0R00V 0 Ω, 1/4W 1206 Chip resistor
6 2 R15 R16 Panasonic ERJ-8GEYJ431V 430 Ω, 1/4W 1206 Chip resistor
7 1 R13 Panasonic ERJ-8GEYJ101V 100 Ω, 1/4W 1206 Chip resistor
8 1 R10 Panasonic ERJ-8ENF2002V 20 kΩ, 1/4W 1206 Chip resistor
9 6 R1 R2 R3 R4 R5
R7
Panasonic ERJ-8GEYJ302V 3 kΩ, 1/4W 1206 Chip resistor
10 3 R6 R12 R14 Panasonic ERJ-8ENF1002V 10 kΩ, 1/4W 1206 Chip resistor
11 1 R9 Bourns 3214W-203E 20 kΩ, BOURNS_32X4W Series
5T Pot
12 1 R11 Bourns 3214W-104E 100 kΩ, BOURNS_32X4W Series
5T Pot
13 1 J6 Samtec TSM-105-01-T-DV 5X2X0.1, 10-pin 3A isolated power
socket
14 2 J2 J4 Samtec TSM-110-01-S-DV-M 10X2X.1, 20 pin 0.025”sq SMT
socket
15 2 J1 J5 On-Shore
Technology
ED555/3DS 3-Pin terminal connector
16 1 U1 Texas Instruments DAC8574IPW 16 Bit, quad voltage output, serial
input I
2
C DAC, TSSOP-16
17 1 U2 Texas Instruments OPA627AU 8-SOP(D) precision op amp
18 1 U3 Texas Instruments REF02AU +5V, 8-SOP(D) precision voltage
reference
19 1 U8 Texas Instruments OPA2132UA 8-SOP(D) dual precision op amp
20 7 TP1 TP2 TP3 TP4
TP5 TP6 TP7
Mill-max 2348-2-01-00-00-07-0 Turret terminal test point
21 2 P2 P4 (see Note) Samtec SSW-110-22-S-D-VS-P 20 Pin 0.025”sq SMT terminal
strips
22 1 P6 (see Note) Samtec SSW-105-F-D-VS-K 3A Isolated 10-pin power header
23 6 W3 W7 W8 W9
W10 W15
Molex 22-03-2021 2 Position jumper_ 0.1” spacing
24 8 W1 W2 W4 W5
W6 W11 W12
W13
Molex 22-03-2031 3 Position Jumper_ 0.1” spacing
Note: P2, P4 & P6 parts are not shown in the schematic diagram. All the P designated parts are installed in the bottom side of the
PC Board opposite the J designated counterpart. Example, J2 is installed on the topside while P2 is installed in the bottom
side opposite of J2.