Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsDev KitsPCB design board

Bill of Materials

2-5

Physical Description

2.2 Bill of Materials

Table 2-1.Parts Lists

Item # Qty Designator Manufacturer Part Number Description

1 1 R2 Panasonic ERJ-8GEY0R00V 0 Ω, 1/4 W, 1206 chip resistor

2 2 C8, C9 Panasonic ECUV1H103KBM 0.01 µF, 1206 multilayer ceramic

capacitor

3 4 C4, C5, C6, C7 Panasonic ECJ3VB1C104K 0.01 µF, 1206 multilayer ceramic

capacitor

4 1 C11 Panasonic ECUV1H102JCH 1 nF, 1206 multilayer ceramic

capacitor

5 3 W6, W7, W8 Samtec TSW-102-07-L-S 2 position jumper_0.1 ’’ spacing

6 4 W1, W2, W3, W4 Samtec TSW-103-07-L-S 3 position jumper_0.1 ’’ spacing

7 2 J8, J9 Samtec IPT1-105-01-S-D-VS 5X2X0.1 10-pin 3A isolated power

header

8 3 R6, R7, R8 Panasonic ERJ-8ENF1002V 10 kΩ, 1/4 W 1206 chip resistor

9 1 R3 Bourns 3214W-103E 10 kΩ, BOURNS_32X4W series 5T

Pot

10 4 C1, C2, C3, C10 Kemet C1210C106K8PAC 10 µF, 1206 multilayer ceramic X5R

capacitor

11 1 R4 Panasonic ERJ-8ENF2002V 20 kΩ, 1/4 W 1206 chip resistor

12 3 J2, J3, J4 Samtec TSM-110-01-S-DV-M 10X2X0.1 20-pin 0.025”” sq SMT

terminal strips

13 1 J1 Samtec TSM-116-01-S-DV-M 16X2X0.1 32-pin 0.025”” sq SMT

terminal strips

14 1 R1 Panasonic ERJ-8GEYJ330V 33 Ω, 1/4 W, 1206 chip resistor

15 1 R5 Bourns 3214W-104E 100 kΩ, BOURNS_32X4W series 5T

Pot

16 1 J5 (see Note) AMP (Tyco) 227699-2 PCB mounted BNC—amphenol

17 1 U1 Texas Instruments DAC8541 16-bit, 32-TQFP DAC

18 1 J7 Lumberg KRMZ2 2-pin terminal screw connector

19 1 J6 Lumberg KRMZ4 4-pin terminal screw connector

20 1 U2 Texas Instruments OPA627AU 8-SOP (D) precision op amp

21 1 U3 Texas Instruments REF02AU 5 V, 8-SOP (D) precision voltage

reference

22 3 TP1, TP2, TP3 Cambion 180-7337-02-05 Turret terminal test point

23 1 W5 Samtec TSW-103-07-L-D 3X2X0.1 6-pin IDC header

24 3 P2, P3, P4

(see Note)

Samtec SSW-110-22-S-D-VS-P 20 pin 0.025”” sq SMT socket

25 1 P1 (see Note) Samtec SSW-116-22-S-D-VS-P 32 pin 0.025”” sq SMT socket

26 2 P8, P9 (see Note) Samtec IPS1-105-01-S-D-VS 3A isolated power socket

Note: P1, P2, P3, P4, P8, and P9 parts are not shown in the schematic diagram. All the P designated parts are installed in the

bottom side of the PC board opposite the J designated counterpart. Example, J1 is installed on the topside while P1 is

installed in the bottom side opposite of J1.

J5 is an optional output terminal and is not installed.