Datasheet

Bill of Materials
2-12
2.3 Bill of Materials
Table 2−1.DAC7654 Bill of Materials
Item # Qty Designator Manufacturer Part Number Description
1 2 C9 C10 Panasonic ECUV1H103KBM
0.01µF, 1206 Multilayer
Ceramic Capacitor
2 5 C1 C2 C7 C8 C11 Panasonic ECJ3VB1C104K
0.1µF, 1206 Multilayer
Ceramic Capacitor
3 1 C12 Panasonic ECUV1H102JCH
1nF, 1206 Multilayer
Ceramic Capacitor
4 3 C4 C5 C6 Kemet C1210C106K8PAC
10µF, 1210 Multilayer
Ceramic X5R Capacitor
5 1 C3 Kemet ECU−V1H471KBM
470pF, 50V, 1206 Multilayer
Ceramic Capacitor SMD
6 3 R3 R7 R9 Panasonic ERJ−8GEY0R00V
0 Ohm, 1/4W 1206 Chip
Resistor
7 2 R1 R2 Panasonic ERJ−8ENF1240V
124 Ohms, 1%, 1/8W 1206
Chip Resistor
8 1 R4 Panasonic ERJ−8GEYJ101V
100 Ohms, 1/4W 1206 Chip
Resistor
9 1 R8 Panasonic ERJ−8GEYJ202V
2K Ohms, 5%, 1/4W 1206
Chip Resistor
10 4 R5 R6 R12 R13 Panasonic ERJ−8ENF1002V
10K Ohms, 1/4W 1206 Chip
Resistor
11 2 Q1 Q2 Panasonic 2SC24050RL
FET Transistor NPN
35VCEO 50MA MINI−3P
12 1 J5 Molex 22−03−2041
4 Position Jumper_ .1”
spacing
13 1 J6 Samtec TSM−105−01−T−DV
5X2X0.1
10−pin 3A Isolated Power
Socket
14 2 J2 J4 Samtec TSM−110−01−S−DV−M
10X2X.1, 20 Pin .025”sq
SMT Socket
15 2 J1 J3 On−Shore Technology ED555/3DS 3−Pin Terminal Connector
16 1 U1 Texas Instruments DAC7654IDGS
16−bit, Quad Voltage Out-
put, Serial Input DAC,
PQFP−64
17 1 U2 Texas Instruments OPA627AU
8−SOP(D) Precision Op
Amp
18 7
TP1 TP2 TP3 TP4
TP5 TP6 TP7
Mill−Max 2348−2−01−00−00−07−0 Turret Terminal Test Point
19 2 P2 P4 (see Note) Samtec SSW−110−22−S−D−VS−P
20PIN .025”sq SMT Termi-
nal Strips
20 1 P6 (see Note) Samtec SSW−105−22−F−D−VS−K
3A Isolated 10−pin Power
Header
21 9
W6 W7 W8 W9
W14 W15 W16
W22 W24
Molex 22−03−2021
2 Position Jumper_ .1”
spacing
22 15
W1 W2 W3 W4
W5 W10 W11
W12 W13 W20
W21 W23 W25
W26 W27
Molex 22−03−2031
3 Position Jumper_ .1”
spacing
Note: P2, P4 & P6 parts are not shown in the schematic diagram. All the P designated parts are installed in the
bottom side of the PC Board opposite the J designated counterpart. Example, J2 is installed on the topside
while P2 is installed in the bottom side opposite of J2. Not all parts listed in the BOM are installed in the
EVM as they are specific to the DUT installed.