Datasheet

Bill of Materials
2-13
PCB Design and Performance
2.3 Bill of Materials
Table 2-1.Parts List
Item # Qty Designator Mfr. Part Number Description
1 2 C9 C10 Panasonic ECUV1H103KBM 0.01-µF, 1206 multilayer ceramic capacitor
2 4 C1 C2 C3 C4 Panasonic ECJ3VB1C104K 0.1-µF, 1206 multilayer ceramic capacitor
3 1 C12 Panasonic ECUV1H102JCH 1-nF, 1206 multilayer ceramic capacitor
4 2 C5 C11 Kemet C1210C106K8PAC 10-µF, 1210 multilayer ceramic X5R
capacitor
5 8 R1 R8 R10
R21 R22 R23
R25 R38
Panasonic ERJ-8GEY0R00V 0-Ω, 1/4-W 1206 chip resistor
6 6 R15 R16 R17
R18 R19 R20
Panasonic ERJ-8GEYJ431V 430-Ω, 1/4-W 1206 chip resistor
7 1 R24 Panasonic ERJ-8GEYJ101V 100-Ω,1/4-W 1206 chip resistor
8 1 R10 Panasonic ERJ-8ENF2002V 20-kΩ,1/4-W 1206 chip resistor
9 6 R2 R3 R4 R5
R7 R13
Panasonic ERJ-8GEYJ302V 3-kΩ, 1/4-W 1206 chip resistor
10 2 R6 R12 Panasonic ERJ-8ENF1002V 10-kΩ,, 1/4-W 1206 chip resistor
11 1 R9 Bourns 3214W-203E 20-kΩ, BOURNS_32X4W series 5T pot
12 1 R14 Bourns 3214W-103E 10-kΩ, BOURNS_32X4W series 5T pot
13 1 R11 Bourns 3214W-502E 5-kΩ,, BOURNS_32X4W series 5T pot
14 1 J6 Samtec TSM-105-01-T-DV 5X2X0.1, 10-pin 3 A isolated power socket
15 2 J2 J4 Samtec TSM-110-01-S-DV-M 10X2X.1, 20 Pin 0.025” sq SMT socket
16 2 J1 J5 On-Shore
Technology
ED555/3DS 3-pin terminal connector
DAC7574IDGS 12-bit, quad voltage output, serial input
I
2
C DAC, MSOP-10
17 1 U1
Texas
Instruments
DAC6574IDGS 10-bit, quad voltage output, serial input
I
2
C DAC, MSOP-10
Instruments
DAC5574IDGS 8-bit, quad voltage output, serial input I
2
C
DAC, MSOP-10
18 1 U2 Texas
Instruments
OPA627AU 8-SOP(D) precision op amp
19 1 U3 Texas
Instruments
REF02AU 5-V, 8-SOP(D) precision voltage reference
20 1 U4 Texas
Instruments
DAC8571IDGK 16-bit, voltage output, serial input I
2
C
DAC, MSOP-8
DAC7571IDBVT 12-bit, voltage output, serial input I
2
C
DAC, SOT23-6
21 1 U8
Texas
Instruments
DAC6571IDBVT 10-bit, voltage output, serial input I
2
C
DAC, SOT23-6
Instruments
DAC5571IDBVT 8-bit, voltage output, serial input I
2
C DAC,
SOT23-6
22 6 TP1 TP2 TP3
TP4 TP5 TP6
Mill-max 2348-2-01-00-00-07-0 Turret terminal test point
23 2 P2 P4
(see Note)
Samtec SSW-110-22-S-D-VS-P 20-pin 0.025” square SMT terminal strips
24 1 P6 (see Note) Samtec SSW-105-F-D-VS-K 3-A isolated 10-pin power header
25 5 W7 W8 W10
TP8 TP9
Molex 22-03-2021 2 position jumper, 0.1” spacing
26 11 W1-W6 W9
W11-W14
Molex 22-03-2031 3 position jumper, 0.1” spacing
Note: P2, P4, and P6 parts are not shown in the schematic diagram. All the P designated parts are installed in the bottom side of
the PC board opposite the J designated counterpart. Example, J2 is installed on the topside while P2 is installed in the
bottom side opposite of J2. Not all parts listed in the BOM are installed in the EVM as they are specific to the DUT installed.