User's Manual
Table Of Contents
- Table of Contents
- Preface
- 1 eZ430-Chronos™ Overview
- 2 Getting Started
- 3 eZ430-Chronos Software
- 3.1 Overview
- 3.2 eZ430-Chronos Sports Watch Software
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.2.1.1 Time Mode
- 3.2.1.2 Alarm Mode
- 3.2.1.3 Temperature Mode
- 3.2.1.4 Altimeter Mode
- 3.2.1.5 Heart Rate Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.6 Speed Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.7 Tilt Mode
- 3.2.2 Detailed Feature Overview - Modes Using the Bottom LCD Line
- 3.2.2.1 Date Mode
- 3.2.2.2 Stopwatch Mode
- 3.2.2.3 Battery Voltage Mode
- 3.2.2.4 Acceleration Mode - RF
- 3.2.2.5 PowerPoint Mode - RF
- 3.2.2.6 Sync Mode - RF
- 3.2.2.7 Calorie/Distance Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.2.8 Wireless Update - RF
- 3.2.2.9 Chronos-to-Chronos (C2C) Mode
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.3 eZ430-Chronos Control Center PC Software
- 3.4 eZ430-Chronos Watch Data Logger
- 3.5 Data Logger PC Software
- 3.6 eZ430-Chronos Software Projects
- 4 eZ430-Chronos Hardware
- 4.1 Programming/Reprogramming the eZ430-Chronos Watch: Disassembly and Assembly of the Housing
- 4.2 Functional Description of the eZ430-Chronos Watch
- 4.3 Functional Description of the eZ430-Chronos RF Access Point
- 4.4 Functional Description of the eZ430-Chronos Debug Interface
- 4.5 Schematics, Layout, BOM, and LCD
- 4.6 Access Point Schematics, Layout and BOM
- A Frequently Asked Questions
- B Detailed Hardware Driver Installation Guide
- Important Notices
www.ti.com
eZ430-Chronos Software Projects
3.6.4.4 Upgrading Existing eZ430-Chronos Kits
Earlier eZ430-Chronos kits (production date prior to 04/2010; the production date may be found on bottom
of eZ430-Chronos box) do not support the wireless update feature. Therefore, the kits must be updated
manually. In addition to a new version of the PC software, firmware updates of the RF access point and
the eZ430-Chronos watch are required.
3.6.4.4.1 RF Access Point Update
The CC Debugger is required to reprogram the CC1111 based RF access point. To perform the update,
the SmartRF Flash Programmer software is used to on the PC.
1. Solder a debug interface connector cable onto the CC1111 access point as shown in Figure 3-16.
Figure 3-16. eZ430-Chronos RF Access Point Connection to CC Debugger
CC-Debugger RF Access Point
Pin 1 GND
Pin 2 Vcc
Pin 3 P2.2 (DC)
Pin 4 P2.1 (DD)
Pin 7 RST
Pin 9 Vcc
2. Connect RF access point to CC Debugger and press the "Reset". The LED on the CC Debugger
should become green.
3. Launch the SmartRF Programmer software
4. Open .hex file according to frequency in C:\Program Files\Texas Instruments\eZ430-
Chronos\Recovery\RF Access Point
5. Select "Erase, program and verify"
6. Clock "Perform actions"
49
SLAU292D–November 2009–Revised March 2011 eZ430-Chronos Software
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated