User's Manual
Table Of Contents
- Table of Contents
- Preface
- 1 eZ430-Chronos™ Overview
- 2 Getting Started
- 3 eZ430-Chronos Software
- 3.1 Overview
- 3.2 eZ430-Chronos Sports Watch Software
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.2.1.1 Time Mode
- 3.2.1.2 Alarm Mode
- 3.2.1.3 Temperature Mode
- 3.2.1.4 Altimeter Mode
- 3.2.1.5 Heart Rate Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.6 Speed Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.1.7 Tilt Mode
- 3.2.2 Detailed Feature Overview - Modes Using the Bottom LCD Line
- 3.2.2.1 Date Mode
- 3.2.2.2 Stopwatch Mode
- 3.2.2.3 Battery Voltage Mode
- 3.2.2.4 Acceleration Mode - RF
- 3.2.2.5 PowerPoint Mode - RF
- 3.2.2.6 Sync Mode - RF
- 3.2.2.7 Calorie/Distance Mode - RF Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
- 3.2.2.8 Wireless Update - RF
- 3.2.2.9 Chronos-to-Chronos (C2C) Mode
- 3.2.1 Detailed Feature Overview - Modes Using the Top LCD Line
- 3.3 eZ430-Chronos Control Center PC Software
- 3.4 eZ430-Chronos Watch Data Logger
- 3.5 Data Logger PC Software
- 3.6 eZ430-Chronos Software Projects
- 4 eZ430-Chronos Hardware
- 4.1 Programming/Reprogramming the eZ430-Chronos Watch: Disassembly and Assembly of the Housing
- 4.2 Functional Description of the eZ430-Chronos Watch
- 4.3 Functional Description of the eZ430-Chronos RF Access Point
- 4.4 Functional Description of the eZ430-Chronos Debug Interface
- 4.5 Schematics, Layout, BOM, and LCD
- 4.6 Access Point Schematics, Layout and BOM
- A Frequently Asked Questions
- B Detailed Hardware Driver Installation Guide
- Important Notices
www.ti.com
Install Demo Application, Drivers and Firmware
2.2 Install Demo Application, Drivers and Firmware
The eZ430-Chronos PC software supports Windows
®
and Linux
®
(Ubuntu 9.10) operating systems.
Download the latest eZ430-Chronos Software and Source Code Installer (SLAC341) for Windows and
(SLAC388) for Linux from the eZ430-Chronos web page at www.ti.com/chronos or open it from the
included CD.
2.2.1 Windows® Installation
1. Unzip the archive and run Chronos-Setup.exe.
2. Respond to the prompts to install the software. During the installation a separate window opens for the
Windows driver installation. Accept the driver installation.
NOTE: The eZ430-Chronos access point driver may not be certified by Microsoft. Therefore,
Windows may generate a warning. Allow the driver installation to continue.
3. When installation finishes, connect the eZ430-Chronos RF USB access point to the PC and follow the
Windows driver installation (see Section 2.3).
4. If prompted for the driver for the TI CC1111 Low-Power RF to USB CDC Serial Port, allow Windows to
'Install the software automatically'. This can be done only if the eZ430-Chronos PC Software package
has already been installed.
5. Open the eZ430-Chronos Control Center program. A shortcut is available on the Desktop and the Start
Menu under Programs > Texas Instruments > eZ430-Chronos > eZ430-Chronos Control Center.
For a detailed driver installation, see Appendix B.
2.2.2 Linux® Installation
The eZ430-Chronos PC software for Linux requires TCL/Tk. If the Linux distribution does not already
include TCL/Tk yet, install both with the apt-get command:
sudo apt-get install tcl8.5
sudo apt-get install tk8.5
To generate keyboard events and mouse clicks through the watch buttons, xdotool is required. Install with
the apt-get command:
sudo apt-get install xdotool
The PC now has the infrastructure for the eZ430-Chronos PC Software. Continue with the eZ430-Chronos
installation:
1. Unzip the archive and run Chronos-Setup.
2. Respond to the prompts to install the software.
3. Insert the eZ430-Chronos RF USB access point to the PC.
4. Check the /dev directory for new entry /dev/ttyACMx, where x specifies the number of the port.
5. Set the COM variable in eZ430-Chronos_CC_1_2.tcl and eZ430-Chronos_Datalogger_1_2.tcl if the
USB RF access point is not mounted as /dev/ttyACM0
6. Set script files to executable: chmod u+x ./eZ430-Chronos_CC_1_2.tcl and chmod u+x ./eZ430-
Chronos_Datalogger_1_2.tcl
7. Launch the script from terminal ./eZ430-Chronos_CC_1_2.tcl
NOTE: Linux is supported by the eZ430-Chronos Control Center and eZ430-Chronos Data Logger
PC applications. The eZ430-Chronos software package also contains all source code for the
watch module and access point, which are provided for Code Composer Studio and the IAR
Embedded Workbench. Both IDEs are currently only available for Windows. CrossWorks
from Rowley Associates supports Linux and MacOS but requires manual project setup.
MSPGCC may be used for Linux as well.
13
SLAU292D–November 2009–Revised March 2011 Getting Started
Submit Documentation Feedback
Copyright © 2009–2011, Texas Instruments Incorporated