Datasheet
MOTOROLA CMOS LOGIC DATAMC14060B
2
MAXIMUM RATINGS* (Voltages Referenced to V
SS
)
Symbol Parameter Value Unit
V
DD
DC Supply Voltage – 0.5 to + 18.0 V
V
in
, V
out
Input or Output Voltage (DC or Transient) – 0.5 to V
DD
+ 0.5 V
I
in
, I
out
Input or Output Current (DC or Transient),
per Pin
± 10 mA
P
D
Power Dissipation, per Package† 500 mW
T
stg
Storage Temperature – 65 to + 150
C
T
L
Lead Temperature (8–Second Soldering) 260
C
* Maximum Ratings are those values beyond which damage to the device may occur.
†Temperature Derating:
Plastic “P and D/DW” Packages: – 7.0 mW/ C From 65 C To 125 C
Ceramic “L” Packages – 12 mW/ C From 100 C To 125 C
ELECTRICAL CHARACTERISTICS (Voltages Referenced to V
SS
)
Characteristic
Symbol
V
DD
Vdc
– 55 C 25 C 125 C
Unit
Characteristic
Symbol
V
DD
Vdc
Min Max Min Typ # Max Min Max
Unit
Output Voltage “0” Level
V
in
= V
DD
or 0
V
OL
5.0
10
15
—
—
—
0.05
0.05
0.05
—
—
—
0
0
0
0.05
0.05
0.05
—
—
—
0.05
0.05
0.05
V
V
in
= 0 or V
DD
“1” Level V
OH
5.0
10
15
4.95
9.95
14.95
—
—
—
4.95
9.95
14.95
5.0
10
15
—
—
—
4.95
9.95
14.95
—
—
—
V
Input Voltage
“0” Level
(V
O
= 4.5 or 0.5 V)
(V
O
= 9.0 or 1.0 V)
(V
O
= 13.5 or 1.5 V)
(V
O
= 0.5 or 4.5 V) “1” Level
(V
O
= 1.0 or 9.0 V)
(V
O
= 1.5 or 13.5 V)
V
IL
5.0
10
15
—
—
—
1.5
3.0
4.0
—
—
—
2.25
4.50
6.75
1.5
3.0
4.0
—
—
—
1.5
3.0
4.0
V
(V
O
= 0.5 or 4.5 V)
“1” Level
(V
O
= 1.0 or 9.0 V)
(V
O
= 1.5 or 13.5 V)
V
IH
5.0
10
15
3.5
7.0
11.0
—
—
—
3.5
7.0
11.0
2.75
5.50
8.25
—
—
—
3.5
7.0
11.0
—
—
—
V
Input Voltage
“0” Level
(V
O
= 4.5 Vdc) (For Input 11
(V
O
= 9.0 Vdc) and Output 10)
(V
O
= 13.5 Vdc)
(V
O
= 0.5 Vdc) “1” Level
(V
O
= 1.0 Vdc)
(V
O
= 1.5 Vdc)
V
IL
5.0
10
15
—
—
—
1.0
2.0
2.5
—
—
—
2.25
4.50
6.75
1.0
2.0
2.5
—
—
—
1.0
2.0
2.5
Vdc
(V
O
= 0.5 Vdc)
“1” Level
(V
O
= 1.0 Vdc)
(V
O
= 1.5 Vdc)
V
IH
5.0
10
15
4.0
8.0
12.5
—
—
—
4.0
8.0
12.5
2.75
5.50
8.25
—
—
—
4.0
8.0
12.5
—
—
—
Vdc
Output Drive Current
(V
OH
= 2.5 V) (Except Source
(V
OH
= 4.6 V)
Pins 9 and 10)
(V
OH
= 9.5 V)
(V
OH
= 13.5 V)
(V
OL
= 0.4 V) Sink
(V
OL
= 0.5 V)
(V
OL
= 1.5 V)
I
OH
5.0
5.0
10
15
– 3.0
– 0.64
– 1.6
– 4.2
—
—
—
—
– 2.4
– 0.51
– 1.3
– 3.4
– 4.2
– 0.88
– 2.25
– 8.8
—
—
—
—
– 1.7
– 0.36
– 0.9
– 2.4
—
—
—
—
mA
(V
OL
= 0.4 V) Sink
(V
OL
= 0.5 V)
(V
OL
= 1.5 V)
I
OL
5.0
10
15
0.64
1.6
4.2
—
—
—
0.51
1.3
3.4
0.88
2.25
8.8
—
—
—
0.36
0.9
2.4
—
—
—
mA
Input Current I
in
15 — ± 0.1 — ±0.00001 ± 0.1 — ± 1.0 µA
Input Capacitance (V
in
= 0) C
in
— — — — 5.0 7.5 — — pF
Quiescent Current
(Per Package)
I
DD
5.0
10
15
—
—
—
5.0
10
20
—
—
—
0.005
0.010
0.015
5.0
10
20
—
—
—
150
300
600
µA
Total Supply Current**†
(Dynamic plus Quiescent,
Per Package)
(C
L
= 50 pF on all outputs,
all buffers switching)
I
T
5.0
10
15
I
T
= (0.25 µA/kHz) f + I
DD
I
T
= (0.54 µA/kHz) f + I
DD
I
T
= (0.85 µA/kHz) f + I
DD
µA
# Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
**The formulas given are for the typical characteristics only at 25 C.
This device contains protection circuitry to
guard against damage due to high static
voltages or electric fields. However, pre-
cautions must be taken to avoid applications of
any voltage higher than maximum rated volt-
ages to this high–impedance circuit. For proper
operation, V
in
and V
out
should be constrained
to the range V
SS
(V
in
or V
out
) V
DD
.
Unused inputs must always be tied to an
appropriate logic voltage level (e.g., either V
SS
or V
DD
). Unused outputs must be left open.