Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLogic ICsLogic IC - Demultiplexer, decoder Decoder/demultiplexer Single supply PDIP 16

CD54ACT139, CD74ACT139

DUAL 2-LINE TO 4-LINE DECODERS/DEMULTIPLEXERS

SCHS337 – MARCH 2003

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

AC Types Feature 1.5-V to 5.5-V Operation

and Balanced Noise Immunity at 30% of the

Supply Voltage

Buffered Inputs

Incorporate Two Enable Inputs to Simplify

Cascading and/or Data Reception

Speed of Bipolar F, AS, and S, With

Significantly Reduced Power Consumption

Balanced Propagation Delays

±24-mA Output Drive Current

– Fanout to 15 F Devices

SCR-Latchup-Resistant CMOS Process and

Circuit Design

Exceeds 2-kV ESD Protection Per

MIL-STD-883, Method 3015

description/ordering information

The ’ACT139 devices are dual 2-line to 4-line decoders/demultiplexers designed for 4.5-V to 5.5-V V

operation. These devices are designed to be used in high-performance memory-decoding or data-routing

applications requiring very short propagation delay times. In high-performance memory systems, these

decoders can be used to minimize the effects of system decoding. When used with high-speed memories

utilizing a fast enable circuit, the delay times of these decoders and the enable time of the memory usually are

less than the typical access time of the memory. This means that the effective system delay introduced by the

decoders is negligible.

The active-low enable (G

) input can be used as a data line in demultiplexing applications. These

decoders/demultiplexers feature fully buffered inputs, each of which represents only one normalized load to its

driving circuit.

ORDERING INFORMATION

PACKAGE

†

ORDERABLE

PART NUMBER

TOP-SIDE

MARKING

PDIP – E Tube CD74ACT139E CD74ACT139E

Cto125

SOIC M

Tube CD74ACT139M

ACT139M

–

55°C

125°C

SOIC

–

Tape and reel CD74ACT139M96

ACT139M

CDIP – F Tube CD54ACT139F3A CD54ACT139F3A

†

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines

are available at www.ti.com/sc/package.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

1Y0

1Y1

1Y2

1Y3

GND

2Y0

2Y1

2Y2

2Y3

CD54ACT139 ...F PACKAGE

CD74ACT139 . . . E OR M PACKAGE

(TOP VIEW)

On products compliant to MIL-PRF-38535, all parameters are tested

unless otherwise noted. On all other products, production

processing does not necessarily include testing of all parameters.

Summary of content (14 pages)

PAGE 1
CD54ACT139, CD74ACT139 DUAL 2-LINE TO 4-LINE DECODERS/DEMULTIPLEXERS SCHS337 – MARCH 2003 D D D D D D D D CD54ACT139 . . . F PACKAGE CD74ACT139 . . . E OR M PACKAGE (TOP VIEW) AC Types Feature 1.5-V to 5.
PAGE 2
CD54ACT139, CD74ACT139 DUAL 2-LINE TO 4-LINE DECODERS/DEMULTIPLEXERS SCHS337 – MARCH 2003 FUNCTION TABLE (each decoder/demultiplexer) INPUTS OUTPUTS SELECT G B A Y0 Y1 Y2 Y3 H X X H H H H L L L L H H H L L H H L H H L H L H H L H L H H H H H L logic diagram (positive logic) 4 1Y0 1 1G 5 6 1A Select Inputs 1Y1 1Y2 2 7 3 1B 1Y3 Data Outputs 12 2Y0 2G 15 11 2Y1 10 2A Select Inputs 2B 2Y2 14 9 13 2Y3 absolute maximum ratings over operating free-air t
PAGE 3
CD54ACT139, CD74ACT139 DUAL 2-LINE TO 4-LINE DECODERS/DEMULTIPLEXERS SCHS337 – MARCH 2003 recommended operating conditions (see Note 3) –55°C to 125°C TA = 25°C –40°C to 85°C UNIT MIN MAX MIN MAX MIN MAX 4.5 5.5 4.5 5.5 4.5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current –24 IOL ∆t/∆v Low-level output current Input transition rise or fall rate High-level input voltage 2 2 0.8 2 V 0.
PAGE 4
CD54ACT139, CD74ACT139 DUAL 2-LINE TO 4-LINE DECODERS/DEMULTIPLEXERS SCHS337 – MARCH 2003 switching characteristics over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V, CL = 50 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B Y tPLH tPHL G Y PARAMETER –55°C to 125°C –40°C to 85°C UNIT MIN MAX MIN MAX 2.9 11.5 3.1 10.5 2.9 11.5 3.1 10.5 3 12 3.2 10.9 3 12 3.2 10.
PAGE 5
CD54ACT139, CD74ACT139 DUAL 2-LINE TO 4-LINE DECODERS/DEMULTIPLEXERS SCHS337 – MARCH 2003 PARAMETER MEASUREMENT INFORMATION S1 R1 = 500 Ω From Output Under Test 2 × VCC Open GND CL = 50 pF (see Note A) R2 = 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND tw 3V 1.5 V Input LOAD CIRCUIT 1.5 V 0V VOLTAGE WAVEFORMS PULSE DURATION CLR Input 3V Reference Input 3V 1.5 V 1.5 V 0V 0V trec Data Input 3V 1.5 V CLK th tsu 1.
PAGE 6
PACKAGE OPTION ADDENDUM www.ti.
PAGE 7
PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.
PAGE 8
PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device CD74ACT139M96 Package Package Pins Type Drawing SOIC D 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 10.3 2.1 8.0 W Pin1 (mm) Quadrant 16.
PAGE 9
PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD74ACT139M96 SOIC D 16 2500 333.2 345.9 28.
PAGE 10
PAGE 11
PAGE 12
PAGE 13
PAGE 14
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.