Datasheet
MOTOROLA CMOS LOGIC DATAMC14069UB
2
ELECTRICAL CHARACTERISTICS (Voltages Referenced to V
SS
)
Characteristic
Symbol
V
DD
Vdc
– 55 C 25 C 125 C
Unit
Characteristic
Symbol
V
DD
Vdc
Min Max Min Typ # Max Min Max
Unit
Output Voltage
“0” Level
V
in
= V
DD
V
in
= 0 “1” Level
V
OL
5.0
10
15
—
—
—
0.05
0.05
0.05
—
—
—
0
0
0
0.05
0.05
0.05
—
—
—
0.05
0.05
0.05
Vdc
V
in
= 0
“1” Level
V
OH
5.0
10
15
4.95
9.95
14.95
—
—
—
4.95
9.95
14.95
5.0
10
15
—
—
—
4.95
9.95
14.95
—
—
—
Vdc
Input Voltage
“0” Level
(V
O
= 4.5 Vdc)
(V
O
= 9.0 Vdc)
(V
O
= 13.5 Vdc)
“1” Level
(V
O
= 0.5 Vdc)
(V
O
= 1.0 Vdc)
(V
O
= 1.5 Vdc)
V
IL
5.0
10
15
—
—
—
1.0
2.0
2.5
—
—
—
2.25
4.50
6.75
1.0
2.0
2.5
—
—
—
1.0
2.0
2.5
Vdc
“1” Level
(V
O
= 0.5 Vdc)
(V
O
= 1.0 Vdc)
(V
O
= 1.5 Vdc)
V
IH
5.0
10
15
4.0
8.0
12.5
—
—
—
4.0
8.0
12.5
2.75
5.50
8.25
—
—
—
4.0
8.0
12.5
—
—
—
Vdc
Output Drive Current
(V
OH
= 2.5 Vdc) Source
(V
OH
= 4.6 Vdc)
(V
OH
= 9.5 Vdc)
(V
OH
= 13.5 Vdc)
I
OH
5.0
5.0
10
15
– 3.0
– 0.64
– 1.6
– 4.2
—
—
—
—
– 2.4
– 0.51
– 1.3
– 3.4
– 4.2
– 0.88
– 2.25
– 8.8
—
—
—
—
– 1.7
– 0.36
– 0.9
– 2.4
—
—
—
—
mAdc
(V
OL
= 0.4 Vdc) Sink
(V
OL
= 0.5 Vdc)
(V
OL
= 1.5 Vdc)
I
OL
5.0
10
15
0.64
1.6
4.2
—
—
—
0.51
1.3
3.4
0.88
2.25
8.8
—
—
—
0.36
0.9
2.4
—
—
—
mAdc
Input Current I
in
15 — ± 0.1 — ±0.00001 ± 0.1 — ± 1.0 µAdc
Input Capacitance
(V
in
= 0)
C
in
— — — — 5.0 7.5 — — pF
Quiescent Current
(Per Package)
I
DD
5.0
10
15
—
—
—
0.25
0.5
1.0
—
—
—
0.0005
0.0010
0.0015
0.25
0.5
1.0
—
—
—
7.5
15
30
µAdc
Total Supply Current**†
(Dynamic plus Quiescent,
Per Gate) (C
L
= 50 pF)
I
T
5.0
10
15
I
T
= (0.3 µA/kHz) f + I
DD
/6
I
T
= (0.6 µA/kHz) f + I
DD
/6
I
T
= (0.9 µA/kHz) f + I
DD
/6
µAdc
Output Rise and Fall Times**
(C
L
= 50 pF)
t
TLH
, t
THL
= (1.35 ns/pF) C
L
+ 33 ns
t
TLH
, t
THL
= (0.60 ns/pF) C
L
+ 20 ns
t
TLH
, t
THL
= (0.40 ns/pF) C
L
+ 20 ns
t
TLH
,
t
THL
5.0
10
15
—
—
—
—
—
—
—
—
—
100
50
40
200
100
80
—
—
—
—
—
—
ns
Propagation Delay Times**
(C
L
= 50 pF)
t
PLH
, t
PHL
= (0.90 ns/pF) C
L
+ 20 ns
t
PLH
, t
PHL
= (0.36 ns/pF) C
L
+ 22 ns
t
PLH
, t
PHL
= (0.26 ns/pF) C
L
+ 17 ns
t
PLH
,
t
PHL
5.0
10
15
—
—
—
—
—
—
—
—
—
65
40
30
125
75
55
—
—
—
—
—
—
ns
#Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
**The formulas given are for the typical characteristics only at 25 C.
†To calculate total supply current at loads other than 50 pF:
I
T
(C
L
) = I
T
(50 pF) + (C
L
– 50) Vfk
where: I
T
is in µA (per package), C
L
in pF, V = (V
DD
– V
SS
) in volts, f in kHz is input frequency, and k = 0.002.
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However,
precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance
circuit. For proper operation, V
in
and V
out
should be constrained to the range V
SS
≤ (V
in
or V
out
) ≤ V
DD
.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either V
SS
or V
DD
). Unused outputs must
be left open.