User manual

Factory Configuration (FCFG) www.ti.com
9.2.1.46 FLASH_OTP_DATA4 Register (Offset = 308h) [reset = X]
FLASH_OTP_DATA4 is shown in Figure 9-67 and described in Table 9-69.
Flash OTP Data 4
Figure 9-67. FLASH_OTP_DATA4 Register
31 30 29 28 27 26 25 24
STANDBY_MO STANDBY_PW_SEL_INT_WRT DIS_STANDBY DIS_IDLE_INT VIN_AT_X_INT_WRT
DE_SEL_INT_ _INT_WRT _WRT
WRT
R-1h R-X R-1h R-1h R-X
23 22 21 20 19 18 17 16
STANDBY_MO STANDBY_PW_SEL_EXT_WRT DIS_STANDBY DIS_IDLE_EXT VIN_AT_X_EXT_WRT
DE_SEL_EXT_ _EXT_WRT _WRT
WRT
R-1h R-X R-1h R-1h R-X
15 14 13 12 11 10 9 8
STANDBY_MO STANDBY_PW_SEL_INT_RD DIS_STANDBY DIS_IDLE_INT VIN_AT_X_INT_RD
DE_SEL_INT_ _INT_RD _RD
RD
R-1h R-X R-1h R-1h R-7h
7 6 5 4 3 2 1 0
STANDBY_MO STANDBY_PW_SEL_EXT_RD DIS_STANDBY DIS_IDLE_EXT VIN_AT_X_EXT_RD
DE_SEL_EXT_ _EXT_RD _RD
RD
R-1h R-X R-1h R-1h R-7h
Table 9-69. FLASH_OTP_DATA4 Register Field Descriptions
Bit Field Type Reset Description
31 STANDBY_MODE_SEL_I R 1h
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 0, this value will be
NT_WRT
written to FLASH:CFG.STANDBY_MODE_SEL by flash device
driver FW when a flash write operation is initiated.
30-29 STANDBY_PW_SEL_INT R X
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 0, this value will be
_WRT
written to FLASH:CFG.STANDBY_PW_SEL by flash device driver
FW when a flash write operation is initiated.
28 DIS_STANDBY_INT_WR R 1h
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 0, this value will be
T
written to FLASH:CFG.DIS_STANDBY by flash device driver FW
when a flash write operation is initiated.
27 DIS_IDLE_INT_WRT R 1h
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 0, this value will be
written to FLASH:CFG.DIS_IDLE by flash device driver FW when a
flash write operation is initiated.
26-24 VIN_AT_X_INT_WRT R X
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 0, this value will be
written to FLASH:FSEQPMP.VIN_AT_X by flash device driver FW
when a flash write operation is initiated.
23 STANDBY_MODE_SEL_ R 1h
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 1, this value will be
EXT_WRT
written to FLASH:CFG.STANDBY_MODE_SEL by flash device
driver FW when a flash write operation is initiated.
22-21 STANDBY_PW_SEL_EXT R X
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 1, this value will be
_WRT
written to FLASH:CFG.STANDBY_PW_SEL by flash device driver
FW when a flash write operation is initiated.
20 DIS_STANDBY_EXT_WR R 1h
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 1, this value will be
T
written to FLASH:CFG.DIS_STANDBY by flash device driver FW
when a flash write operation is initiated.
19 DIS_IDLE_EXT_WRT R 1h
If AON_SYSCTL:PWRCTL.EXT_REG_MODE = 1, this value will be
written to FLASH:CFG.DIS_IDLE by flash device driver FW when a
flash write operation is initiated.
762
Device Configuration SWCU117A–February 2015–Revised March 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated