User manual

www.ti.com Interrupts and Events Registers
Table 4-91. UDMACH14BSEL Register Field Descriptions (continued)
Bit Field Type Reset Description
58h = Port capture event from IOC, configured by
IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM
PORT_EVENT3 wil be routed here.
59h = Port capture event from IOC, configured by
IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM
PORT_EVENT4 wil be routed here.
5Ah = Port capture event from IOC, configured by
IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM
PORT_EVENT4 wil be routed here.
5Bh = Port capture event from IOC, configured by
IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM
PORT_EVENT6 wil be routed here.
5Ch = Port capture event from IOC, configured by
IOC:IOCFGn.PORT_ID. Events on ports configured with ENUM
PORT_EVENT7 wil be routed here.
5Dh = CRYPTO result available interupt event, the corresponding
flag is found here CRYPTO:IRQSTAT.RESULT_AVAIL. Controlled
by CRYPTO:IRQSTAT.RESULT_AVAIL
5Eh = CRYPTO DMA input done event, the correspondingg flag is
CRYPTO:IRQSTAT.DMA_IN_DONE. Controlled by
CRYPTO:IRQEN.DMA_IN_DONE
5Fh = RFC RAT event 4, configured by RFC_RAT:RATEV.OEVT4
60h = RFC RAT event 5, configured by RFC_RAT:RATEV.OEVT5
61h = RFC RAT event 6, configured by RFC_RAT:RATEV.OEVT6
62h = RFC RAT event 7, configured by RFC_RAT:RATEV.OEVT7
63h = Watchdog non maskable interrupt event, controlled by
WDT:CTL.INTTYPE
64h = Software event 0, triggered by SWEV.SWEV0
65h = Software event 1, triggered by SWEV.SWEV1
66h = Software event 2, triggered by SWEV.SWEV2
67h = Software event 3, triggered by SWEV.SWEV3
68h = TRNG Interrupt event, controlled by TRNG:IRQEN.EN
69h = AON wakeup event, corresponds flags are here
AUX_EVCTL:EVTOMCUFLAGS.AON_WU_EV
6Ah = AUX Compare A event, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPA
6Bh = AUX Compare B event, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.AUX_COMPB
6Ch = AUX TDC measurement done event, corresponds to the flag
AUX_EVCTL:EVTOMCUFLAGS.TDC_DONE and the AUX_TDC
status AUX_TDC:STAT.DONE
6Dh = AUX timer 0 event, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.TIMER0_EV
6Eh = AUX timer 1 event, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.TIMER1_EV
6Fh = Autotake event from AUX semaphore, configured by
AUX_SMPH:AUTOTAKE
70h = AUX ADC done, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.ADC_DONE
71h = AUX ADC FIFO watermark event, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.ADC_FIFO_ALMOST_FULL
72h = Loopback of OBSMUX0 through AUX, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.OBSMUX0
73h = AUX ADC interrupt event, corresponds to
AUX_EVCTL:EVTOMCUFLAGS.ADC_IRQ. Status flags are found
here [AUX_EVCTL:EVTOMCUFLAGS.ADC*]
74h = AUX observation loopback
75h = DMA single request event from AUX, configured by
AUX_EVCTL:DMACTL
76h = DMA burst request event from AUX, configured by
AUX_EVCTL:DMACTL
77h = RTC periodic event controlled by
363
SWCU117A–February 2015–Revised March 2015 Interrupts and Events
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated