Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsDev KitsPCB design board

Quick Start Guide

SLUU468–December 2010

bq76PL536PGM-1 Programming Board

This document covers the initial connection and installation of the Texas Instruments bq76PL536 program

(OTP) board, P/N bq76PL536PGM-1. For device details and setting up the secondary protection, see the

bq76PL536 data sheet.

Contents

1 Software and Hardware Requirements .................................................................................. 2

2 Software Installation ........................................................................................................ 2

3 Connecting bq76PL536PGM and bq76PL536EVM Boards ........................................................... 2

4 EPROM Programming Procedures ....................................................................................... 3

5 Warnings and Troubleshooting ............................................................................................ 9

6 Advanced Mode View Detail ............................................................................................. 10

7 Support ...................................................................................................................... 13

8 Packing List ................................................................................................................ 13

List of Figures

1 bq76PL536EVM-3 .......................................................................................................... 3

2 bq76PL536PGM-1 .......................................................................................................... 3

3 Setting Trimming Value .................................................................................................... 4

4 Creating Programmable Image ........................................................................................... 4

5 Entering Optional Product Data ........................................................................................... 5

6 Saving Image File........................................................................................................... 5

7 Loading Image to bq76PL536 OTP EPROM Programmer ............................................................ 5

8 Loading Image to bq76PL536 OTP EPROM Programmer ............................................................ 6

9 Check Hardware Setup .................................................................................................... 6

10 Detecting IC.................................................................................................................. 6

11 IC Detected. IC Inserted Correctly........................................................................................ 7

12 Warning for NO IC or Inserting Incorrectly .............................................................................. 7

13 Programming IC............................................................................................................. 8

14 Passing or Failing. IC is Programmed Correctly........................................................................ 8

15 Passing/Failing. IC Failed to Program Fail Count Increases by 1 .................................................... 8

16 Completed EPROM Programming. Insert a New IC and Repeat From Step 5. .................................... 9

17 Warning for NO IC or IC Inserted Incorrectly............................................................................ 9

18 Reprogramming Trimmed IC............................................................................................. 10

19 Advanced Mode Main View .............................................................................................. 11

20 Copying Measurements Data to Clipboard ............................................................................ 11

21 Connect to Dongle ........................................................................................................ 11

22 Program Image ............................................................................................................ 12

23 Comparing OTP. OTP Matches ......................................................................................... 12

24 Comparing OTP. OTP Does not Match ................................................................................ 12

25 Checking for Blank OTP. OTP is Blank ................................................................................ 13

26 Checking for Blank OTP. OTP is not Blank ............................................................................ 13

SLUU468–December 2010 bq76PL536PGM-1 Programming Board

Submit Documentation Feedback

Summary of content (14 pages)

PAGE 1
Quick Start Guide SLUU468 – December 2010 bq76PL536PGM-1 Programming Board This document covers the initial connection and installation of the Texas Instruments bq76PL536 program (OTP) board, P/N bq76PL536PGM-1. For device details and setting up the secondary protection, see the bq76PL536 data sheet. 1 2 3 4 5 6 7 8 Contents Software and Hardware Requirements .................................................................................. 2 Software Installation .......................................
PAGE 2
Software and Hardware Requirements www.ti.com 1 Software and Hardware Requirements 1.1 Software Requirements 1. Install bq76PL536EVM-3 evaluation software, version 2.1.17 or higher. 2. Install bq76PL536PGM-1 OTP EPROM programming software. 3. Install Aardvark driver. 1.2 Hardware Requirements 1. bq76PL536PGM-1 programming board kit 2. bq76PL536EVM-3. See the bq76PL536EVM-3 user's guide for more details. 3. Aardvark Host Adapter 2 Software Installation 2.
PAGE 3
EPROM Programming Procedures www.ti.com Figure 1. bq76PL536EVM-3 3.2 Connecting bq76PL536PGM Figure 2. bq76PL536PGM-1 1. 2. 3. 4. 5. 4 Connect the USB cable to the Aardvark adapter and your PC. Connect the Aardvark ribbon cable to the 10-pin header on the bq76PL536PGM programmer board. Run the bq76PL536 OTP EPROM programmer software on your PC. Check for 22-V and 7-V LEDs on the board and GUI. See Figure 9. If all of the LEDs are not ON, select Connect to Dongle (F2), or repeat the preceding steps.
PAGE 4
EPROM Programming Procedures www.ti.com 4. Run bq76PL536 OTP EPROM Programmer Software. 5. Load the image created with bq76PL536EVM ( Figure 7 and Figure 8). 6. Insert the integrated circuit (IC) into the socket. Check for pin 1 orientation. See Figure 10. The 22V and 7V LEDs must be on. If not, press the F2 function key, "Connect to Dongle". See Figure 21. 7. Test the IC. Click the Click to Detect selection. 8. Separate pass and fail IC. 9. Insert a new IC, and repeat from step 5. 10.
PAGE 5
EPROM Programming Procedures www.ti.com Figure 5. Entering Optional Product Data Figure 6. Saving Image File Figure 7.
PAGE 6
EPROM Programming Procedures www.ti.com Figure 8. Loading Image to bq76PL536 OTP EPROM Programmer Figure 9. Check Hardware Setup Figure 10.
PAGE 7
EPROM Programming Procedures www.ti.com Figure 11. IC Detected. IC Inserted Correctly Figure 12. Warning for NO IC or Inserting Incorrectly Discard this IC if inserted incorrectly.
PAGE 8
EPROM Programming Procedures www.ti.com Figure 13. Programming IC Figure 14. Passing or Failing. IC is Programmed Correctly Figure 15. Passing/Failing.
PAGE 9
Warnings and Troubleshooting www.ti.com Figure 16. Completed EPROM Programming. Insert a New IC and Repeat From Step 5. 5 Warnings and Troubleshooting 5.1 No IC or IC Inserted Incorrectly 1. See Figure 17. Error message pops up. 2. Discard the IC if IC is inserted incorrectly 5.2 Reprogramming Trimmed (Programmed) IC EPROM (OTP) is a one-time-only programmable memory. ICs must not be programmed more than one time. It is possible to damage the device if programmed twice.
PAGE 10
Advanced Mode View Detail www.ti.com Figure 18. Reprogramming Trimmed IC 6 Advanced Mode View Detail Advanced mode provides tools for users to get more detailed information for debugging purposes. This mode is not recommended for production operator. 6.1 Copy Measurement Data to Clipboard • 6.2 Connect to Dongle - F2 • 6.3 6.4 • Program OTP trim value to IC (Figure 22). • Click icon or F5. Compare OTP Compare IC OTP content (Figure 23and Figure 24).
PAGE 11
Advanced Mode View Detail www.ti.com 6.6 Refresh Figure 19. Advanced Mode Main View Figure 20. Copying Measurements Data to Clipboard Figure 21.
PAGE 12
Advanced Mode View Detail www.ti.com Figure 22. Program Image Figure 23. Comparing OTP. OTP Matches Figure 24. Comparing OTP.
PAGE 13
Support www.ti.com Figure 25. Checking for Blank OTP. OTP is Blank Figure 26. Checking for Blank OTP. OTP is not Blank 7 Support Contact your local TI sales office for technical support. Support is also available through the TI E2E™ community forum at http://e2e.ti.com/support/power_management/default.aspx . 8 Packing List Line QTY EA P/N Description 1 1 ea Bq76PL536PGM PCB assembly (x = rev level) 2 1 ea Aardvark adapter USB→SPI (FW Rev 3.
PAGE 14
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.