Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsDev KitsPCB design board

www.ti.com

Circuit Module Physical Layouts and Bill of Materials

Table 3. Bill of Materials

RefDes Value Description Size Part Number MFR

C1–C8, C10, 0.1μF Capacitor, Ceramic, 0.1μF, 50 V, X7R, 20% 0603 STD Any

C12–16, C18,

C19, C23, C24

C11, C17, C20 1.0μF Capacitor, Ceramic, 1.0 μF, 25 V, X7R, 20% 0805 STD Any

C21, C22 100pF Capacitor, Ceramic, 100pF, 50 V, X7R, 10% 0603 STD Any

C9 0.22μF Capacitor, Ceramic, 0.22μF, 25 V, X7R, 20% 0603 STD Any

D1–D3 MBRX02560 Diode, Schottky, 250mA, 60V SOD-323 MBRX02560 Micro

Commercial

D4 MM3Z5V6C Diode, Zener, 5.6V, 200mw SOD323 MM3Z5V6C Fairchild

J1 22-05-3041 Header, Friction Lock Assy., 4-pin right angle 0.400 × 0.500 22-05-3041 Molex

Q1, Q2 Si1023X MOSFET, P-ch, –20V, –350mA, 1.2Ω SC-89 Si1023x Vishay

Q3 NDS351AN MOSFET, N-ch, 30-V, 1.4A, 0.16-Ω SOT23 NDS351AN Fairchild

Q4, Q5, Q6 Si4435DY MOSFET, P-ch, 30-V, 8.0-A, 20-mΩ SO8 Si4435DY Siliconix

R1–R9, R30 1K Resistor, Chip, 1kΩ, 1/16-W, 5% 0603 Std Std

R10–R13 100 Resistor, Chip, 100 Ω, 1/4-W, 5% 1206 CRCW1206100RJNEA Vishay

R14 .010 75ppm Resistor, Chip, 0.010 Ω, 1-W, 1% 2512 WSL-2512-010 1% R86 Vishay

R15, R16, R29, 100 Resistor, Chip, 100 Ω, 1/16-W, 5% 0603 Std Std

R31, R32

R17, R19 220K Resistor, Chip, 220 kΩ, 1/16-W, 5% 0603 Std Std

R18 1M Resistor, Chip, 1MΩ, 1/16-W, 5% 0603 Std Std

R20, R25 3M Resistor, Chip, 3 MΩ, 1/16-W, 5% 0603 Std Std

R21, R22, R24 5.1K Resistor, Chip, 5.1kΩ, 1/16-W, 5% 0603 Std Std

R23 301 Resistor, Chip, 301-Ω, 1-W, 10% 2512 CRCW2512301RFKEG Vishay

R27, R28 200 Resistor, Chip, 200-Ω, 1/16-W, 5% 0603 Std Std

RT1, RT2 10K Thermistor, 10 kΩ 0.095 × 0.150 BN35-3H103FB-50 Mitsubishi

or 103AT-2 Material or

Semitec

TB1 ED1514 Terminal Block, 2-pin, 6-A, 3,5 mm 0.27 × 0.25 ED555/2DS OST

TB2, TB4, TB5 ED1515 Terminal Block, 3-pin, 6-A, 3,5 mm 0.41 × 0.25 ED555/3DS OST

TP1, TP2, Test Point, White, Thru Hole Color Keyed 0.100 × 0.100 inch 5002 Keystone

TP5–TP7, TP9

U1 BQ29412DCT IC, Voltage Protection for 2, 3, 4 Cell Lion , SSOP-08 BQ29412DCT TI

2nd Protection, 4.45 v OVP

U2 BQ3060PW IC, SBS 1.1-Compliant gas gauge and protection TSSOP-24 BQ3060PW TI

-- PCB HPA328 Any

QTY Connector

2 J1 mate Connector, Female, 0.100-inch Centers Molex 22-01-3047

8 N/A Terminals, Crimp, Tin Molex 08-50-0114

N/A Wire, Insulated 24 AWG, Red, 18 Inches (±3 inches)(USB_5V) Alpha 1854-3

N/A Wire, Insulated 24 AWG, White, 18 Inches (±3 inches)(SCL) Alpha 1854-1

N/A Wire, Insulated 24 AWG, Black, 18 Inches (±3 inches)(GND) Alpha 1854-2

N/A Wire, Insulated 24 AWG, Brown, 18 Inches (±3 inches) (SDA) Alpha 1854-7

1 N/A Heatshrink 1" Any Any

Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.

2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.

3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.

4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFR's

components.

5. Make one SMBus connector wire assembly for each assembly produced, from J1 mate, 4–24 AWG wires and Crimp terminals. Wire colors

for Pin numbers are listed below. The wire assembly shall have a J1 mate on each end.

Red - Pin # 4 (Signal USB_5V)

Brown - Pin # 3 (Signal SDA)

White - Pin # 2 (Signal SCL)

Black - Pin # 1 (GND)

SLUU342–October 2009 bq3060EVM-001 SBS 1.1 Compliant Advanced Gas Gauge Battery

Management Solution EVM

Submit Documentation Feedback