Datasheet

www.ti.com Board Layout, Schematic, and Bill of Materials
Table 6. Bill of Materials (continued)
COUNT
RefDes Value Description Size Part Number RefDes
-001 -003 -004 -005 -006 -007
1 1 1 1 1 1 R18 30.1k Resistor, Chip, 1/16W, 1% 0603 STD STD
1 1 1 1 1 1 R19 5.23k Resistor, Chip, 1/16W, 1% 0603 STD STD
1 1 1 1 1 1 R24 768 Resistor, Chip, 1/16W, 1% 0603 STD STD
16 16 16 16 16 16 TP1 TP3-11 TP13-17 TP19 5002 Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone
1 1 1 1 1 1 TP2 131-4244-00 Adaptor, 3.5-mm probe clip ( or 131-5031-00) 0.200 inch 131-4244-00 Tektronix
2 2 2 2 2 2 TP12 TP18 5001 Test Point, Black, Thru Hole Color Keyed 0.100 x 0.100 inch 5001 Keystone
1 0 0 0 0 0 U1 BQ24190RGE IC, I2C Controlled 4A Single Cell USB / Adaptor Charger With Narrow QFN-24 BQ24190RGE TI
VDC Power Path Management and USB OTG
0 0 0 0 0 0 U1 BQ24191RGE IC, I2C Controlled 4A Single Cell USB / Adaptor Charger With Narrow QFN-24 BQ24191RGE TI
VDC Power Path Management
0 1 0 0 0 0 U1 BQ24192RGE IC, I2C Controlled 4A Single Cell USB / Adaptor Charger With Narrow QFN-24 BQ24192RGE TI
VDC Power Path Management and USB OTG
0 0 1 0 0 0 U1 BQ24192IRGE IC, I2C Controlled 4A Single Cell USB / Adaptor Charger With Narrow QFN-24 BQ24192IRGE TI
VDC Power Path Management and USB OTG
0 0 0 1 0 0 U1 BQ24193RGE IC, I2C Controlled 4A Single Cell USB / Adaptor Charger With Narrow QFN-24 BQ24193RGE TI
VDC Power Path Management and USB OTG
0 0 0 0 1 0 U1 BQ24196RGE IC, I2C Controlled 2.5A Single Cell USB / Adaptor Charger With Narrow QFN-24 BQ24196RGE TI
VDC Power Path Management and USB OTG
0 0 0 0 0 1 U1 BQ24292iRGE IC, I2C Controlled 4A Single Cell USB / Adaptor Charger With Narrow QFN-25 BQ24292iRGE TI
VDC Power Path Management and USB OTG
10 10 10 10 10 10 -- Shunt, 100-mil, Black 0.100 929950-00 3M
1 1 1 1 1 1 -- PCB, bq2419xEVM-021, 3"x3" PWR021 Any
1 1 1 1 1 1 -- Label (See note 5) 1.25 x 0.25 inch THT-13-457-10 Brady
4 4 4 4 4 4 - SJ-5303 Rubber foot (see note 6) .044" X 0.20" SJ-5303 3M
Notes: 1. These assemblies are ESD sensitive, observe ESD precautions.
2. These assemblies must be clean and free from flux and all contaminants. Use of no-clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components.
5. Install label after final wash. Text shall be 8 pt font. Text shall be per Label Information.
6. Install after final wash.
Label Information
Assembly number Text
PWR021-001 bq24190EVM-021
PWR021-003 bq24192EVM-021
PWR021-004 bq24192IEVM-021
PWR021-005 bq24193EVM-021
PWR021-006 bq24196EVM-021
PWR021-007 bq24292iEVM-021
19
SLUUA14C–October 2012–Revised August 2013 bq24190/2/2i/3/6 and bq24292i EVM (PWR021) User's Guide
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated