Datasheet

www.ti.com

Board Layout, Schematic, and Bill of Materials

4.3 Bill of Materials

bq24150 bq24151 bq24152 bq24153 bq24155 bq24156 bq24159 RefDes Value Description Size Part Number MFR

-001 -002 -003 -004 -005 -006 -007

1 1 1 1 1 1 1 C1 1mF Capacitor, Ceramic, X5R, 16V, ±10% 603 GRM188R61C105K Murata

1 1 1 1 1 1 1 C2 4.7mF Capacitor, Ceramic, X7R, 16V, ±10% 805 GRM21BR71C475K Murata

2 2 2 2 2 2 2 C3, C9 10mF Capacitor, Ceramic, X5R, 6.3V, ±20% 603 GRM188R60J106M Murata

2 2 2 2 2 2 2 C4, C5 1mF Capacitor, Ceramic, X5R, 10V, ±10% 402 GRM155R61A105K Murata

1 1 1 1 1 1 1 C6 10nF Capacitor, Ceramic, X5R, 16V, ±10% 402 GRM155R61C103K Murata

2 2 2 2 2 2 2 C7, C8 0.1mF Capacitor, Ceramic, X7R, 16V, ±10% 402 GRM155R71C104K Murata

1 1 1 1 1 1 1 D1 Green Diode, LED, Green, 2.1-V, 20-mA, 6-mcd 603 LTST-C190GKT Liteon

1 1 1 1 1 1 1 D2 BAT54C Diode, Dual Schottky, 200-mA, 30-V SOT23 BAT54C Vishay-Liteon

1 1 1 1 1 1 1 J1 ED1514/2DS Terminal Block, 2-pin, 6-A, 3.5mm 0.27 x 0.25 inch ED1514/2DS OST

3 3 3 3 3 3 3 J2–J4 ED1515/3DS Terminal Block, 3-pin, 6-A, 3,5mm 0.41 x 0.25 inch ED1515/3DS OST

1 1 1 1 1 1 1 J5 2510-6002UB Connector, Male Straight 2x5 pin, 100mil 0.338 x 0.788 2510-6002UB 3M

spacing, 4 Wall inch

3 3 3 3 3 3 3 JMP1–JMP4 PEC03SAAN Header, 3-pin, 100mil spacing 0.100 inch x 3 PEC03SAAN Sullins

2 2 2 2 2 2 2 JMP3,JMP5 PEC02SAAN Header, 2-pin, 100mil spacing 0.100 inch x 2 PEC02SAAN Sullins

4 4 4 4 2 4 3 929950-00 Shorting jumpers, 2-pin, 100mil spacing, 929950-00 3M/ESD

1 1 1 1 1 1 1 L1 1.0mH 2.5mmx2mm, 1.0mH, ±30%, 1.5A 0.11x0.09 inch LQM2HPN1R0MJ0 or Murata or FDK or

MIPS2520D1R0 or TOKO or

MDT2520-CN1R0M or CP1008 Inter-Technical

1 1 1 1 1 1 1 R1 0.068 Resistor, Chip, 68mΩ, 125mW, 5% 402 ERJ-2BWJR068X Panasonic

1 1 1 1 1 1 1 R2 5.1k Resistor, Chip, 5.1kΩ, 1/16-W, 5% 603 Std Std

1 1 1 1 1 1 1 R3 10k Resistor, Chip, 10kΩ, 1/16-W, 5% 603 Std Std

1 0 0 0 0 0 0 U1 BQ24150RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24150RGY TI

Li-Polymer Battery

0 1 0 0 0 0 0 U1 BQ24151RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24151RGY TI

Li-Polymer Battery

0 0 1 0 0 0 0 U1 BQ24152RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24152RGY TI

Li-Polymer Battery

0 0 0 1 0 0 0 U1 BQ24153RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24153RGY TI

Li-Polymer Battery

0 0 0 0 1 0 0 U1 BQ24155RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24155RGY TI

Li-Polymer Battery

0 0 0 0 0 1 0 U1 BQ24156RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24156RGY TI

Li-Polymer Battery

0 0 0 0 0 0 1 U1 BQ24159RGY IC, Battery Charger for Single-Cell Li-Ion and QFN-14 BQ24159RGY TI

Li-Polymer Battery

1 1 1 1 1 1 1 -- HPA255 PCB, 2.0 In x 2.0 In x 0.031 In PCB Any

Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.

2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.

3. These assemblies mut comply with workmanship standards IPC-A-610 Class 2.

SLUU366A–March 2010–Revised April 2010 bq2415x RGY EVM (HPA255)

Submit Documentation Feedback