Datasheet

Bill of Materials, Board Layouts and Schematics

www.ti.com

Table 4. Bill of Materials (continued)

Count RefDes Value Description Size Part Number MFR

2 R17, R18 100k Resistor, Chip, 1/16W, 1% 603 STD STD

1 R19 4.99k Resistor, Chip, 1/16W, 1% 603 STD STD

2 R2, R3 3.9 Resistor, Chip, 1/4W, 5% 1206 STD STD

1 R20 32.4k Resistor, Chip, 1/16W, 1% 603 STD STD

1 R4 10 Resistor, Chip, 1/10W, 1% 805 STD STD

0 R6 NONE Resistor, Chip, 1/16W, 1% 805 STD STD

1 R7 0.01 Resistor, Chip, 1/2 watt, 1.0% 1206 WSL1206R0100FEA Vishay

1 R8 0 Resistor, Chip, 1/16W, 5% 603 STD STD

1 R9 5.23k Resistor, Chip, 1/16W, 1% 603 STD STD

0 SH1 None Short jumper

1 TP 131-4244-00 Adaptor, 3.5-mm probe clip ( or 131-5031-00) 0.200 inch 131-4244-00 Tektronix

1 TP1 VCC Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

0 TP2, TP4, NONE Test Point, White, Thru Hole Color Keyed 0.02 x 0.02 inch STD STD

TP5

1 TP3 VREF Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP6 REGN Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP7 TS Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP8 GND Test Point, Black, Thru Hole Color Keyed 0.100 x 0.100 inch 5001 Keystone

1 TP9 STAT Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP10 CELL Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP11 CMOD Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP12 ISET1 Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 TP13 ISET2 Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone

1 U1 BQ24130RHL IC, 1.6-MHz High Efficiency Synchronous VQFN BQ24130RHL TI

Switch-Mode Li-Ion and Li-Polymer Battery

Charger

1 — PCB, 2.500 In X 2.500 In x 0.0062 In 2.500 In X 2.500 In HPA624 Any

4 929950-00 Shorting jumper, 2-pin, 100mil spacing 929950-00 3M/ESD

Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.

2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.

3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.

4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components.

600-kHz Synchronous Switch-Mode Li-Ion and Li-Polymer Host-Controlled SLVU495B–July 2011–Revised January 2012

Battery Charger With Integrated MOSFETs

Submit Documentation Feedback