Datasheet

www.ti.com

List of Materials

Table 4. bq24123EVM-002 List of Materials

(1) (2)

REFERENCE QTY DESCRIPTION SIZE MFR PART NUMBER

DESIGNATOR

C1, C2, C4 3 Capacitor, ceramic, 10 µ F, 25 V, X5R, 20% 1206 Panasonic ECJ-3YB1E106M

C9 0 Capacitor, ceramic, 10 µ F, 25 V, X5R, 20% 1206 Panasonic ECJ-3YB1E106M

C3 0 Capacitor, ceramic, 0.1 µ F, 16 V, X7R, 10% 603 Panasonic ECJ-1VB1C104K

C5, C7, C8 3 Capacitor, ceramic, 0.1 µ F, 16 V, X7R, 10% 603 Panasonic ECJ-1VB1C104K

C6 1 Capacitor, ceramic, 0.1 µ F, 16 V, X7R, 10% 603 Panasonic 160-1183-1-ND

D1 1 Diode, LED, green, 2.1 V, 20 mA, 6 mcd 603 Liteon 160-1183-1-ND

D2 1 Diode, LED, green, 2.1 V, 20 mA, 6 mcd 603 Liteon 160-1183-1-ND

D3 1 Diode, LED, red, 1.8 V, 20 mA, 20 mcd 603 Liteon 160-1181-1-ND

J1 1 Terminal block, 2-pin, 6 A, 3.5 mm 75525 OST ED1514

J2, J3 2 Terminal block, 4-pin, 6 A, 3.5 mm 0.55 × 0.25 OST ED1516

J4 1 Terminal block, 3-pin, 6 A, 3.5 mm 0.41 × 0.25 Sullins ED1515

J5, J6, J8, J9 4 Header, 3-pin, 100 mil spacing, (36-pin strip) 34100 Sullins PTC36SAAN

J7 1 Header, 3-pin, 100 mil spacing, (36-pin strip) 34100 Sullins PTC36SAAN

J10 1 Header, 3-pin, 100 mil spacing, (36-pin strip) 34100 3M PTC36SAAN

6 Shunt, 100 mil, black 0.100 Sumida 929950-00

L1 1 Inductor, SMT, 10 µ H, 1.84 A, 49 mW 0.315 × 0.287 Vishay CDRH74-100

R1 1 Resistor, chip, 1.5 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-1501-F

R10 1 Resistor, chip, 4.99 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-4991-F

R11, R13, R14 3 Resistor, chip, 10 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-1002-F

R12 1 Resistor, chip, 0 Ω , 1/16-W, 1% 603 Vishay CRCW0603-0000-F

R2, R3 2 Resistor, chip, 1.5 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-1501-F

R4 1 Resistor, chip, 0.1 Ω , W, 1% 2010 Vishay CRCW1210-0R10F

R5, R7 0 Resistor, chip, 200 k Ω , 1/8-W, 1% 805 Vishay CRCW0805-2003-F

R6 1 Resistor, chip, 0 Ω , 1/16-W, 1% 603 Vishay CRCW0603-00R0-F

R8, R9 2 Resistor, chip, 7.5 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-7501-F

U1 1 IC, advanced Li-Ion and Li-Pol charge management RHL-20 TI bq24123RHL

— 1 PCB, 2.0 In × 1.9 In × 0.031 In Any HPA171

(1)

C9 can be installed by the customer if using long cables (inductive load)

(2)

Place shunts as follows (Jumper pin orientation: pin 1: top (toward RD), pin 2: center, pin 3-bottom). Place shunts on J5, J6,

J7-1/2 (LED); J9-2/3 (LOW); J8-2 (optional)

SLUU236A – March 2006 – Revised November 2007 Using the bq2412x (bqSWITCHER™) EVM 13

Submit Documentation Feedback