Datasheet

www.ti.com
List of Materials
Table 6. bq24115EVM-004 List of Materials
(1) (2) (3) (4) (5)
REFERENCE QTY DESCRIPTION SIZE MFR PART NUMBER
DESIGNATOR
C1, C2, C4 3 Capacitor, ceramic, 10 µ F, 25 V, X5R, 20% 1206 Panasonic ECJ-3YB1E106M
C9 0 Capacitor, ceramic, 10 µ F, 25 V, X5R, 20% 1206 Panasonic ECJ-3YB1E106M
C3 1 Capacitor, ceramic, 0.1 µ F, 16 V, X7R, 10% 603 Panasonic ECJ-1VB1C104K
C5, C7, C8 3 Capacitor, ceramic, 0.1 µ F, 16 V, X7R, 10% 603 Panasonic ECJ-1VB1C104K
C6 0 Capacitor, ceramic, 0.1 µ F, 16 V, X7R, 10% 603 Panasonic 160-1183-1-ND
D1 0 Diode, LED, green, 2.1 V, 20 mA, 6 mcd 603 Liteon 160-1183-1-ND
D2 1 Diode, LED, green, 2.1 V, 20 mA, 6 mcd 603 Liteon 160-1183-1-ND
D3 1 Diode, LED, red, 1.8 V, 20 mA, 20 mcd 603 Liteon 160-1181-1-ND
J1 1 Terminal block, 2-pin, 6 A, 3.5 mm 75525 OST ED1514
J2, J3 2 Terminal block, 4-pin, 6 A, 3.5 mm 0.55 × 0.25 OST ED1516
J4 1 Terminal block, 3-pin, 6 A, 3.5 mm 0.41 × 0.25 Sullins ED1515
J5, J6, J8, J9 4 Header, 3-pin, 100 mil spacing, (36-pin strip) 34100 Sullins PTC36SAAN
J7 0 Header, 3-pin, 100 mil spacing, (36-pin strip) 34100 Sullins PTC36SAAN
J10 0 Header, 3-pin, 100 mil spacing, (36-pin strip) 34100 3M PTC36SAAN
4 Shunt, 100 mil, black 0.100 Sumida 929950-00
L1 1 Inductor, SMT, 10 µ H, 1.84 A, 49 mW 0.315 × 0.287 Vishay CDRH74-100
R1 0 Resistor, chip, 1.5 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-1501-F
R10 1 Resistor, chip, 4.99 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-4991-F
R11, R13, R14 3 Resistor, chip, 10 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-1002-F
R12 0 Resistor, chip, 0 Ω , 1/16-W, 1% 603 Vishay CRCW0603-0000-F
R2, R3 2 Resistor, chip, 1.5 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-1501-F
R4 1 Resistor, chip, 0.1 Ω , W, 1% 2010 Vishay CRCW1210-0R10F
R5, R7 2 Resistor, chip, 200 k Ω , 1/8-W, 1% 805 Vishay CRCW0805-2003-F
R6 1 Resistor, chip, 0 Ω , 1/16-W, 1% 603 Vishay CRCW0603-00R0-F
R8, R9 2 Resistor, chip, 7.5 k Ω , 1/16-W, 1% 603 Vishay CRCW0603-7501-F
U1 1 IC, advanced Li-Ion and Li-Pol charge RHL-20 TI bq24115RHL
management
— 1 PCB, 2.0 In × 1.9 In × 0.031 In Any HPA040
(1)
These assemblies are ESD sensitive, ESD precautions shall be observed.
(2)
These assemblies must be clean and free from flux and all contaminants. Refrain from using "no clean" flux on these
assembles.
(3)
These assemblies must comply with workmanship standards IPC-A-610 Class 2.
(4)
C9 can be installed by the customer if using long cables (inductive load)
(5)
Place shunts as follows (Jumper pin orientation: pin 1: top (toward RD), pin 2: center, pin 3-bottom). Place shunts on J8-1/2
(Hi), J5 & J6-1/2 (LED), J9-2/3 (LOW).
Using the bq241xx (bqSWITCHER™)16 SLUU200A – July 2004 – Revised December 2007
Submit Documentation Feedback