Datasheet

Schematic, Physical Layouts and Bill of Materials

www.ti.com

5.3 Bill of Materials

Table 1. HPA506B Bill of Materials

-001 -002 -003 -004 RefDes Value Description Size Part Number MFR

1 1 1 1 C1 1 µF Capacitor, Ceramic, 25V, X5R, 10% 0603 ECJ-1VB1E105K Panasonic

0 0 0 0 C2 Capacitor, Ceramic, 25V, X5R, 10% 0805 ECJ-2FB1E225K Panasonic

1 1 1 1 C3 2.2 µF Capacitor, Ceramic, 10V, X5R, 10% 0603 ECJ-1VB1A225K Panasonic

0 0 0 0 C4 Capacitor, Ceramic, 10V, X5R, 10% 0805 ECJ-2FB1A106K Std

0 0 0 0 C5 Capacitor, Ceramic, 10V, X5R, 10% 0603 ECJ-1VB1A225K Panasonic

2 2 2 2 D1, D2 LTST-C190GKT Diode, LED, Green, 2.1-V, 20-mA, 6-mcd 0603 LTST-C190GKT Lite On

0 0 0 0 D3 BZX84C5V6-7-F Diode, Zener, 5.6-V, 350-mW SOT-23 BZX84C5V6-7-F Diodes

1 1 1 1 J1 ED555/2DS Terminal Block, 2-pin, 6-A, 3.5mm 0.27 x 0.25 inch ED555/2DS OST

1 1 1 1 J2 ED555/4DS Terminal Block, 4-pin, 6-A, 3.5mm 0.55 x 0.25 inch ED555/4DS OST

4 4 4 4 JMP1, JMP2, PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN Sullins

JMP4, JMP5

1 1 1 1 JMP3 PEC03SAAN Header, Male 3-pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN Sullins

1 1 1 1 R1 665 Resistor, Chip, 1/16W, 1% 0603 Std Std

1 0 1 0 R11 50k Potentiometer, 3/8 Cermet, Single-Turn 0.25x0.17 inch 3266W-503-LF Bourns

0 1 0 1 R11 500k Potentiometer, 3/8 Cermet, Single-Turn 0.25x0.17 inch 3266W-504-LF Bourns

2 2 2 2 R2, R4 10k Potentiometer, 3/8 Cermet, Single-Turn 0.25x0.17 inch 3266W-103-LF Bourns

2 2 2 2 R3, R12 1.0k Resistor, Chip, 1/16W, 1% 0603 Std Std

2 2 2 2 R5, R9 1.5k Resistor, Chip, 1/16W, 1% 0603 Std Std

0 0 0 0 R6, R13, R14 Resistor, Chip, 1/16W, 1% 0603 Std Std

1 1 1 1 R7 10k Resistor, Chip, 1/16W, 1% 0603 Std Std

2 2 2 2 R8, R10 0 Resistor, Chip, 1/16W, 1% 0603 Std Std

1 0 0 0 U1 BQ24090DGQ IC, 800mA, Single-Input, Single Cell Li-Ion BATTERY HTSSOP BQ24090DGQ TI

CHARGER

0 1 0 0 U1 BQ24091DGQ IC, 800mA, Single-Input, Single Cell Li-Ion BATTERY HTSSOP BQ24091DGQ TI

CHARGER

0 0 1 0 U1 BQ24092DGQ IC, 800mA, Single-Input, Single Cell Li-Ion BATTERY HTSSOP BQ24092DGQ TI

CHARGER

0 0 0 1 U1 BQ24093DGQ IC, 800mA, Single-Input, Single Cell Li-Ion BATTERY HTSSOP BQ24093DGQ TI

CHARGER

5 5 5 5 Shunt (Note 5) Shunt, 100-mil, Black 0.1 929950-00 3M

1 1 1 1 – PCB, 3 In x 1.85 In x 0.0031 In HPA506 Any

Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.

2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.

3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.

4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components.

5. Apply shunt to JMP1/2/4/5 and JMP3:2/3.

1.0-A Single-Input, Single-Cell Li-Ion Battery Charger SLUU392A–December 2009–Revised June 2010