Datasheet

www.ti.com

5 Bill of Materials

Bill of Materials

Figure 4. Top Assembly View

This section contains the bill of materials required for the EVM.

Table 3. HPA149A Bill of Materials, bq2406xEVM

(1) (2) (3)

bq24060 bq24061 bq24064 Ref Des Value Description Size Part Number MFR

-001 -002 -005

Count

1 1 1 C1 0.1 µ F Capacitor, ceramic, 25V, X7R, 10% 0603 ECJ.-1VB1E104K Panasonic

2 2 2 C2, C3 1 µ F Capacitor, ceramic, 25V, X5R, 10% 0805 ECJ-2FB1E105K Panasonic

1 1 1 D1 Diode, LED, red, 1.8-V, 20-mA, 20-mcd 0603 1600-1181-1-ND Liteon

1 1 1 D2 Diode, LED, green, 2.1-V, 20-mA, 6-mcd 0603 1600-1181-1-ND Liteon

0 0 0 D3 0 Resistor, Chip, 0- Ω , 1/16-W, 1% 0603 Std Std

1 1 1 J1 Terminal block, 2-pin, 6-A, 3,5 mm 0.27 × 0.25 ED1514 OST

2 2 2 J2, J3 Terminal block, 4-pin, 6-A, 3,5 mm 0.55 × 0.25 ED1516 OST

2 2 2 J4, J5 Header, 3-pin, 100-mil spacing, (36-pin strip) 0.100 × 3 PTC36SAAN Sullins

1 1 1 J6 Header, 3-pin, 100-mil spacing, (36-pin strip) 0.100 × 3 PTC36SAAN Sullins

0 0 0 J6

(3)

Header, 2-pin, 100-mil spacing, (36-pin strip) 0.100 × 2 PTC36SAAN Sullins

1 1 1 J7 Header, 2-pin, 100-mil spacing, (36-pin strip) 0.100 in × 2 PTC36SAAN Sullins

1 1 1 R8 0 Resistor, chip, 0- Ω , 1/16-W 1% 0603 Std Std

3 3 3 R1, R2, R5 1.5k Resistor, chip, 1.5-k Ω , 1/16-W 1% 0603 Std Std

1 0 1 R3 1M Resistor, chip, 1-M Ω , 1/16-W 1% 0603 Std Std

1 1 1 R6 1M Resistor, chip, 1-M Ω , 1/16-W 1% 0603 Std Std

0 0 0 R9 1M Resistor, chip, 1-M Ω , 1/16-W 1% 0603 Std Std

1 1 1 R4 1.13K Resistor, chip, 1.13 k Ω , 1/16-W 1% 0603 Std Std

1 1 1 R7 49.9k Resistor, chip, 49.9 k Ω , 1/16-W 1% 0603 Std Std

0 0 0 TP1, TP2, Test Point, 0.032 hole Std Std

TP3

(1)

When J6 is a 2 pin header, Install in J6-1/2

(2)

Install Jumper Shunts, for -001/2/5/6/7, on: J4-1/2 (LED), J5-1/2 (LED), J6-1/2 (LED), and J7-1/2.

Install Jumper Shunts, for -003/4, on: J4-1/2 (LED), J5-1/2 (LED), J6-1 (just pin 1), and J7-1/2

(3)

bq24062/3/5/6 are not released at this time. Check WEB for availability.

SLUU235 – February 2006 bq2406x Evaluation Module 7

Submit Documentation Feedback