Datasheet

Schematic, Physical Layouts and Bill of Materials www.ti.com
5.3 Bill of Materials
-001 -002 RefDes Value Description SIZE Part Number MFR
1 1 C1 1μF Capacitor, Ceramic, 25V, X5R, 10% 0603 ECJ-1VB1E105K Panasonic
0 0 C2 Capacitor, Ceramic, 25V, X5R, 10% 0805 – –
1 1 C3 2.2μF Capacitor, Ceramic, 10V, X5R, 10% 0603 ECJ-1VB1A225K Panasonic
0 0 C4 Capacitor, Ceramic, 10V, X5R, 10% 0805 – –
0 0 C5 Capacitor, Ceramic, 25V, X5R, 10% 0603 – –
2 2 D1, D2 LTST-C190GKT Diode, LED, Green, 2.1-V, 20-mA, 0603 LTST-C190GKT Lite On
6-mcd
0 1 D3 BZX84C5v6-7-F Diode, Zener, 5.6-V, 350-mW SOT-23 BZX84C5v6-7-F Diodes
1 1 J1** ED555/2DS Terminal Block, 2-pin, 6-A, 3.5mm 0.27 x 0.25 inch ED555/2DS OST
1 1 J2** ED555/4DS Terminal Block, 4-pin, 6-A, 3.5mm 0.55 x 0.25 inch ED555/4DS OST
0 2 J3, J4 PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN Sullins
(2-pin strip)
3 3 JMP2, JMP4, PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN Sullins
JMP5 (2-pin strip)
0 0 JMP6 PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN Sullins
(2-pin strip)
1 0 JMP1 PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN Sullins
(2-pin strip)
1 1 JMP3 PEC03SAAN Header, Male 3-pin, 100mil spacing, 0.100 inch x 3 PEC03SAAN Sullins
(3-pin strip)
1 1 R1 675 Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R11 50k Potentiometer, 1/4 in. Cermet, 12-Turn, 0.25x0.17 3266W-1-503LF Bourns
Top-Adjust
0 0 R13, R14 Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R2 10k Potentiometer, 1/4 in. Cermet, 12-Turn, 0.25x0.17 3266W-1-103LF Bourns
Top-Adjust
1 0 R4 10k Potentiometer, 1/4 in. Cermet, 12-Turn, 0.25x0.17 3266W-1-103LF Bourns
Top-Adjust
2 2 R3, R12 1.0k Resistor, Chip, 1/16W, 1% 0603 Std Std
2 2 R5, R9 1.5k Resistor, Chip, 1/16W, 1% 0603 Std Std
0 2 R6, R10 100k Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R7 10k Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R8 0 Resistor, Chip, 1/16W, 1% 0603 Std Std
1 0 U1 BQ24040DSQ IC, 800mA, Single-Input, Single Cell SON-10 BQ24040DSQ TI
Li-Ion BATTERY CHARGER w/wo Auto
Start (ASI/ASO)
0 1 U1 BQ24041DSQ IC, 800mA, Single-Input, Single Cell SON-10 BQ24041DSQ TI
Li-Ion BATTERY CHARGER w/wo Auto
Start (ASI/ASO)
5 5 Shunt (Note 5) Shunt, 100-mil, Black 0.1 929950-00 3M
1 1 -- PCB, 2.9 In x 1.8 In x 0.031 In HPA387 Any
Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.
2. These assemblies must be clean and free from flux and all contaminants.
Use of no-clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ('**') cannot be substituted.
All other components can be substituted with equivalent MFR's components.
5. Apply shunt to JMP1/2/4/5 and JMP3:2/3. Note J3 and J4 are test pins and do not have shunts (jumpers).
8
0.8-A Single-Input, Single-Cell Li-Ion Battery Charger SLUU377–September 2009
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated