Datasheet

bq20z75-V180
www.ti.com SLUSA22 –DECEMBER 2009
TERMINAL FUNCTIONS
TERMINAL
I/O
(1)
DESCRIPTION
NO. NAME
1 DSG O High side N-channel discharge FET gate drive
Battery pack input voltage sense input. It also serves as device wake up when device is in shutdown
2 PACK IA, P
mode.
Positive device supply input. Connect to the center connection of the CHG FET and DSG FET to
3 VCC P
ensure device supply either from battery stack or battery pack input
4 ZVCHG O P-channel pre-charge FET gate drive
High voltage general purpose open drain output. Can be configured to be used in pre-charge
5 GPOD OD
condition
Pre-charge mode setting input. Connect to PACK to enable 0v pre-charge using charge FET
6 PMS I connected at CHG pin. Connect to VSS to disable 0V pre-charge using charge FET connected at
CHG pin.
7 VSS P Negative device power supply input. Connect all VSS pins together for operation of device
8 REG33 P 3.3V regulator output. Connect at least a 2.2μF capacitor to REG33 and VSS
9 TOUT P Termistor bias supply output
10 VCELL+ - Internal cell voltage multiplexer and amplifier output. Connect a 0.1μF capacitor to VCELL+ and VSS
Alert output. In case of short circuit condition, overload condition and watchdog time out this pin will
11 ALERT I/OD
be triggered.
12 PRES I/OD System / Host present input. Pull up to TOUT
13 TS1 IA Temperature sensor 1 input
14 TS2 IA Temperature sensor 2 input
15 PFIN I/OD Fuse blow detection input
16 SAFE I/OD blow fuse signal output
17 SMBD I/OD SMBus data line
18 SMBC I/OD SMBus clock line
19 NC - Not Connected
20 VSS P Negative device power supply input. Connect all VSS pins together for operation of device.
21 VSS P Negative device power supply input. Connect all VSS pins together for operation of device.
22 GSRP IA Coulomb counter differential input. Connect to one side of the sense resistor
23 GSRN IA Coulomb counter differential input. Connect to one side of the sense resistor
24 MRST I Reset input for internal CPU core. connect to RESET for correct operation of device.
25 VSS P Negative device power supply input. Connect all VSS pins together for operation of device.
26 REG25 P 2.5V regulator output. Connect at least a 1μF capacitor to REG25 and VSS
RAM backup input. Connect a capacitor to this pin and VSS to protect loss of RAM data in case of
27 RBI P
short-circuit condition
28 VSS P Negative device power supply input. Connect all VSS pins together for operation of device
29 RESET O Reset output. Connect to MSRT.
30 ASRN IA Short-circuit and overload detection differential input
31 ASRP IA Short-circuit and overload detection differential input
Cell voltage sense input and cell balancing input for the negative voltage of the bottom cell in cell
32 VC5 IA,P
stack.
Cell voltage sense input and cell balancing input for the positive voltage of the bottom cell and the
33 VC4 IA,P
negative voltage of the second lowest cell in cell stack.
Cell voltage sense input and cell balancing input for the positive voltage of the second lowest cell in
34 VC3 IA,P
cell stack and the negative voltage of the second highest cell in 4 cell applications.
Cell voltage sense input and cell balancing input for the positive voltage of the second highest cell
35 VC2 IA,P and the negative voltage of the highest cell in 4 cell applications. Connect to VC3 in 2 cell stack
applications
Cell voltage sense input and cell balancing input for the positive voltage of the highest cell in cell
36 VC1 IA,P
stack in 4 cell applications. Connect to VC2 in 3 or 2 cell stack applications
(1) I = Input, IA = Analog input, I/O = Input/output, I/OD = Input/Open-drain output, O = Output, OA = Analog output, P = Power
Copyright © 2009, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): bq20z75-V180