Datasheet
Table Of Contents
- FEATURES
- DESCRIPTION
- PIN CONNECTIONS
- ABSOLUTE MAXIMUM RATINGS
- DC ELECTRICAL CHARACTERISTICS
- VFC CHARACTERISTICS
- REG CHARACTERISTICS
- SMBus AC SPECIFICATIONS
- HDQ16 AC SPECIFICATIONS
- FUNCTIONAL DESCRIPTION
- General Operation
- Measurements
- Current
- Temperature
- GAS GAUGE OPERATION
- MAIN GAS GAUGE REGISTERS
- Self-Discharge
- Light Discharge or Suspend Current Compensation
- Midrange Capacity Corrections
- Charge Control
- Display Port
- Secondary Protection for Li-ion
- Low-Power Storage Mode
- Device Reset
- COMMUNICATION
- SMBus
- SMBus Protocol
- SMBus Packet Error Checking
- PEC Protocol
- PEC Calculation
- PEC Enable in Master Mode
- SMBus On and Off State
- HDQ16
- Command Codes
- ManufacturerAccess() (0x00); [0x00–0x01]
- RemainingCapacityAlarm() (0x01); [0x01]
- RemainingTimeAlarm() (0x02); [0x02]
- BatteryMode() (0x03); [0x03]
- AtRate() (0x04); [0x04]
- AtRateTimeToFull() (0x05);[0x05]
- AtRateTimeToEmpty() (0x06); [0x06]
- AtRateOK() (0x07); [0x07]
- Temperature() (0x08); [0x08]
- Voltage() (0x09); [0x09]
- Current() (0x0a); [0x0a]
- AverageCurrent() (0x0b); [0x0b]
- MaxError() (0x0c); [0x0c]
- RelativeStateOfCharge() (0x0d); [0x0d]
- AbsoluteStateOfCharge()(0x0e); [0x0e]
- RemainingCapacity() (0x0f); [0x0f]
- FullChargeCapacity() (0x10); [0x10]
- RunTimeToEmpty() (0x11); [0x11]
- AverageTimeToEmpty() (0x12); [0x12]
- AverageTimeToFull() (0x13); [0x13]
- ChargingCurrent() (0x14); [0x14]
- ChargingVoltage() (0x15); [0x15]
- BatteryStatus()(0x16); [0x16]
- CycleCount()(0x17); [0x17]
- DesignCapacity() (0x18); [0x18]
- DesignVoltage() (0x19); [0x19]
- SpecificationInfo() (0x1a); [0x1a]
- ManufactureDate() (0x1b); [0x1b]
- SerialNumber() (0x1c); [0x1c]
- ManufacturerName() (0x20); [0x20–0x2a]
- DeviceName() (0x21); [0x28–0x2b]
- DeviceChemistry() (0x22); [0x30–0x32]
- ManufacturerData() (0x23); [0x38–0x3a]
- Pack Status and Pack Configuration (0x2f); [0x2f]
- OCE
- EDV2
- EINT
- VDQ
- COK
- DOK
- CVOV
- CVUV
- VCELL4–VCELL1 (0x3c–0x3f); [0x3c–0x3f]
- EEPROM
- EEPROM Programming
- Fundamental Parameters
- Cell Characteristics
- Charge Limits and Termination Techniques
- Overvoltage
- Charging Current
- Charge Suspension
- FULLY_CHARGED Bit Clear Threshold
- Fast Charge Termination Percentage
- Cycle Count Threshold
- ΔT/Δt Rate Programming
- ΔT/Δt Holdoff Timer Programming
- Current Taper Termination Characteristics
- PACK OPTIONS
- DMODE
- SEAL
- CSYNC
- CEDV
- VCOR
- CHEM
- LCC0 and LCC1
- Remaining Time and Capacity Alarms
- Secondary Protection Limits for Li-Ion
- Miscellaneous Options
- NE1
- SOT
- HIT
- Cycle Count Initialization
- Control Modes
- NDF
- HPE
- CPE
- LED
- SC
- SM
- MEASUREMENT CALIBRATION
- CONSTANTS AND STRING DATA
- REVISION HISTORY
V
CC
ToPack
Protection
Circuitry
V
CC
S
G
D
SST113
R
5
PACK-
SMBC
SMBD
HDQ
Thermistor
V
CC
V
CC
V
CC
SCL
SDA
A0
A1
A2
WP
V
SS
EEPROM
V
CC
LED1
LED2
LED3
LED4
LED5
CFC
DFC
DISP
ESCL
ESDA
THON
TS
V
SS
bq2060
REG
V
CC
CVON
VCELL
4
VCELL
3
VCELL
2
VCELL
1
RBI
SRC
SR
2
SR
1
SMBC
SMBD
HDQ16
PACK+
bq2060A
SLUS500D –OCTOBER 2001– REVISED OCTOBER 2011
www.ti.com
Figure 5. Battery Pack Application Diagram – LED Display and Series Cell Monitoring
8 Submit Documentation Feedback Copyright © 2001–2011, Texas Instruments Incorporated
Product Folder Link(s): bq2060A