User's Guide SBAU188 – February 2012 AMC1210MB-EVM AMC1210MB-EVM This user's guide describes the characteristics, operation, and use of the AMC1210MB-EVM as part of an evaluation system when used with Texas Instruments delta-sigma (ΔΣ) modulator evaluation modules (EVMs) in resolver or current-shunt applications. A schematic diagram and bill of materials are included in this document. The following related documents are available for download through the Texas Instruments web site at http://www.ti.com.
www.ti.com 1 2 3 4 Contents EVM Overview ............................................................................................................... 3 Hardware Interfaces ........................................................................................................ 3 Software ...................................................................................................................... 6 Schematics and Layout ............................................................................
EVM Overview www.ti.com 1 EVM Overview 1.
Hardware Interfaces 2.2 www.ti.com Resolver Interface Pinout The AMC1210MB-EVM is designed for easy interfacing to resolver applications. Connector J5 is a nine-pin, female-type DSUB connector for connection to a standard resolver. To hold the floating resolver inputs to a predefined common-mode level, a 2.5-V offset is added to the resolver inputs. The AMC1210MB-EVM resolver interface pinout is detailed in Table 2. Table 2. AMC1210MB-EVM Resolver Interface Pinout 2.
Hardware Interfaces www.ti.com 2.4 Jumpers JP1 and JP2 are available to configure the resolver carrier signal driver. The carrier signal may either be driven directly by the AMC1210 or through the OPA1632 operational amplifier. The purpose of the OPA1632 is to provide the ability to filter the carrier signal and continue to be capable of sourcing 85 mA on the carrier. This interface is shown in Table 4. Table 4. AMC1210MB-EVM JP1 and JP2 Interface Jumper 2.
Software 3 www.ti.com Software The program for evaluating the AMC1210MB-EVM is the AMC1210EVM software. This program uses the NI-VISA™ client to communicate with the hardware through a USB port. The program currently runs only on PCs with the Microsoft Windows XP operating system. Windows Vista and Windows 7 are not supported. 3.1 Installation Follow these procedures to install the AMC1210MB-EVM software. Step 1. Install the AMC1210MB-EVM software and LabVIEW™ RunTime Engine software.
Software www.ti.com Figure 2. NI-VISA AMC1210MB-EVM Driver Installation Figure 3.
Software www.ti.com Figure 4. NI-VISA AMC1210MB-EVM Driver Installing Figure 5.
Software www.ti.com Step 3. Verify that installation is completed correctly by opening the Windows Device Manager and locating the driver, as shown in Figure 6. Figure 6. NI-VISA AMC1210MB-EVM Driver Verification 3.2 Using the AMC1210MB-EVM Evaluation Software The AMC1210MB-EVM evaluation software provides two modes of operation: Resolver Demo and Current Shunt. Each mode of operation provides a separate GUI and features for evaluating the AMC1210.
Software www.ti.com The toolbar shown in Figure 8 is present, regardless of the mode of operation of the AMC1210MB-EVM software. The left-most button is used to switch between Current-Shunt Mode and Resolver Demo Mode. The remaining buttons are provided for convenience to quickly access information about the device or visit the TI E2E community for support or device queries. Figure 8.
Software www.ti.com Each filter module also has an enable or disable control located below the register configuration indicators. Only enabled filter modules data are displayed in the Current Shunt Data tab. Figure 10 shows an sample set of collected data in the Current Shunt Data tab, with module 1 enabled and module 2 disabled. The Current Shunt Data tab displays collected data in terms of raw codes instead of voltage because a variety of delta-sigma modulators may be connected to the AMC1210.
Software www.ti.com Figure 12. AMC1210MB-EVM Software Resolver Demo GUI: Position Data Figure 13.
Schematics and Layout www.ti.com 4 Schematics and Layout Schematics for the AMC1210MB-EVM are appended to this user's guide. The bill of materials for the evaluation board is provided in Table 7. NOTE: All components should be compliant with the European Union Restriction on Use of Hazardous Substances (RoHS) Directive. Some part numbers may be either leaded or RoHS. Verify that purchased components are RoHS-compliant.
Schematics and Layout www.ti.com Table 7. Bill of Materials (continued) 4.1 Item Quantity Designator 40 2 N/A 0.100 Shunt - Black Shunts Description 3M Manufacturer 969102-0000-DA Part Number 41 4 N/A BUMPON HEMISPHERE .44X.20 BLACK 3M SJ-5003 (BLACK) PCB Layout Figure 14 and Figure 15 illustrate the silkscreen images for the AMC1210MB-EVM. 3600 mm Figure 14. AMC1210MB-EVM PCB Silkscreen (Top Image) Figure 15. AMC1210MB-EVM PCB Silkscreen (Bottom Image) 4.
Schematics and Layout www.ti.com Figure 16.
Schematics and Layout www.ti.com J1 U1 +3.3VD JTAG /CS /WR /RD /ALE /RST 19 18 17 16 41 40 37 36 48 49 Y1 52 53 8.00MHz C6 74 75 95 96 6 5 2 1 C7 10pF 50 51 10pF 64 +3.3VD R5 4.
Schematics and Layout www.ti.com +5VD +3.3VD +5VD 2 3 4 5 R14 20 21 20 C25 R17 14 22pF 20 C26 C27 C28 1 18 0.1uF 0.1uF 0.1uF +5VD CH B+ CH BCH ACH A+ REFOUT 7 6 CLKIN CLKSEL 2K 2K 2K U6 3 4 15 16 3 1 4 OPA353 5 17 2 13 2 C30 C31 0.1uF 0.1uF 0.1uF 5 4 30 SH2 SH1 Y2 35 36 CLKIN R22 +3.3VD 10k 3 4 OUT GND VCC OE 2 1OE CWX823-032.0M +3.3VD 0.
AMC1210MB-EVM SBAU188 – February 2012 Submit Documentation Feedback
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards.
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions: The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods.
FCC Interference Statement for Class B EVM devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
【Important Notice for Users of this Product in Japan】 】 This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product: 1. 2. 3. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.
EVALUATION BOARD/KIT/MODULE (EVM) WARNINGS, RESTRICTIONS AND DISCLAIMERS For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished electrical equipment and not intended for consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
