Datasheet
Control Parameter Register (addresses 0x01, 0x07, 0x0D and 0x13)
AMC1210
www.ti.com
.............................................................................................................................................................. SBAS372D – APRIL 2006 – REVISED MAY 2009
BIT POSITION BIT DESCRIPTION
Modulator failure flag for Filter 1.
8 MF1 0: Modulator is operating normally for Filter 1
1: Modulator failure for Filter 1
Low-level interrupt flag for Filter 4
7 IFL4 0: Comparator Filter 4 output is above the low limit threshold
1: Comparator Filter 4 output is equal to or below the low level threshold, if enabled
High-level interrupt flag for Filter 4
6 IFH4 0: Comparator Filter 4 output is below the high limit threshold
1: Comparator Filter 4 output is equal to or above the high level threshold, if enabled
Low-level interrupt flag for Filter 3
5 IFL3 0: Comparator Filter 3 output is above the low limit threshold
1: Comparator Filter 3 output is equal to or below the low level threshold, if enabled
High-level interrupt flag for Filter 3
4 IFH3 0: Comparator Filter 3 output is below the high limit threshold
1: Comparator Filter 3 output is equal to or above the high level threshold, if enabled
Low-level interrupt flag for Filter 2
3 IFL2 0: Comparator Filter 2 output is above the low limit threshold
1: Comparator Filter 2 output is equal to or below the low level threshold, if enabled
High-level interrupt flag for Filter 2
2 IFH2 0: Comparator Filter 2 output is below the high limit threshold
1: Comparator Filter 2 output is equal to or above the high level threshold, if enabled
Low-level interrupt flag for Filter 1
1 IFL1 0: Comparator Filter 1 output is above the low limit threshold
1: Comparator Filter 1 output is equal to or below the low level threshold, if enabled
High-level interrupt flag for Filter 1
0 IFH1 0: Comparator Filter 1 output is below the high limit threshold
1: Comparator Filter 1 output is equal to or above the high level threshold, if enabled
The Control Parameter Registers control several parameters for the data acquisition process. The Control
Parameter Register functions include the Manchester decoder calibration status, clock pin direction control,
delta-sigma modulator mode select, sample-and-hold select and time measure mode. Table 14 describes the
Control Parameter Register.
Table 14. Control Parameter Register
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
MS10 MS9 MS8 MS7 MS6 MS5 MS4 MS3 MS2 MS1 MS0 CD SHS TM MOD1 MOD0
'0' '0' '0' '0' '0' '0' '0' '0' '0' '0' '0' '0' '0' '0' '0' '0'
R R R R R R R R R R R RW RW RW RW RW
BIT POSITION BIT DESCRIPTION
15 – 5 MS10 – MS0 Manchester status
Input clock direction.
4 CD 0: Pin CLKx is an input
1: Pin CLKx is an output. The outgoing clock comes from the modulator clock divider.
Sample-and-hold select.
3 SHS 0: Signal SH1 is chosen as sample-and-hold signal
1: Signal SH2 is chosen as sample-and-hold signal
Time measure mode.
0: The time is measured from the last filter update to the last rising edge of the selected
2 TM
sample-and-hold signal
1: The time is measured between two rising edges of the selected sample-and-hold signal
Delta-Sigma Modulator mode.
00: The clock speed is equal to the data rate from the modulator
1 – 0 MOD1 – MOD0 01: The clock rate is half of the data rate from the modulator
10: The data from the modulator is Manchester decoded
11: The clock rate is twice the data rate of the modulator
Copyright © 2006 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Link(s): AMC1210