Datasheet
ADS1013
ADS1014
ADS1015
SBAS473C –MAY 2009–REVISED OCTOBER 2009
www.ti.com
Bits [14:12] MUX[2:0]: Input multiplexer configuration (ADS1015 only)
These bits configure the input multiplexer. They serve no function on the ADS1013/4.
000 : AIN
P
= AIN0 and AIN
N
= AIN1 (default) 100 : AIN
P
= AIN0 and AIN
N
= GND
001 : AIN
P
= AIN0 and AIN
N
= AIN3 101 : AIN
P
= AIN1 and AIN
N
= GND
010 : AIN
P
= AIN1 and AIN
N
= AIN3 110 : AIN
P
= AIN2 and AIN
N
= GND
011 : AIN
P
= AIN2 and AIN
N
= AIN3 111 : AIN
P
= AIN3 and AIN
N
= GND
Bits [11:9] PGA[2:0]: Programmable gain amplifier configuration (ADS1014 and ADS1015 only)
These bits configure the programmable gain amplifier. They serve no function on the ADS1013.
000 : FS = ±6.144V
(1)
100 : FS = ±0.512V
001 : FS = ±4.096V
(1)
101 : FS = ±0.256V
010 : FS = ±2.048V (default) 110 : FS = ±0.256V
011 : FS = ±1.024V 111 : FS = ±0.256V
Bit [8] MODE: Device operating mode
This bit controls the current operational mode of the ADS1013/4/5.
0 : Continuous conversion mode
1 : Power-down single-shot mode (default)
Bits [7:5] DR[2:0]: Data rate
These bits control the data rate setting.
000 : 128SPS 100 : 1600SPS (default)
001 : 250SPS 101 : 2400SPS
010 : 490SPS 110 : 3300SPS
011 : 920SPS 111 : 3300SPS
Bit [4] COMP_MODE: Comparator mode (ADS1014 and ADS1015 only)
This bit controls the comparator mode of operation. It changes whether the comparator is implemented as a
traditional comparator (COMP_MODE = '0') or as a window comparator (COMP_MODE = '1'). It serves no
function on the ADS1013.
0 : Traditional comparator with hysteresis (default)
1 : Window comparator
Bit [3] COMP_POL: Comparator polarity (ADS1014 and ADS1015 only)
This bit controls the polarity of the ALERT/RDY pin. When COMP_POL = '0' the comparator output is active
low. When COMP_POL='1' the ALERT/RDY pin is active high. It serves no function on the ADS1013.
0 : Active low (default)
1 : Active high
Bit [2] COMP_LAT: Latching comparator (ADS1014 and ADS1015 only)
This bit controls whether the ALERT/RDY pin latches once asserted or clears once conversions are within the
margin of the upper and lower threshold values. When COMP_LAT = '0', the ALERT/RDY pin does not latch
when asserted. When COMP_LAT = '1', the asserted ALERT/RDY pin remains latched until conversion data
are read by the master or an appropriate SMBus alert response is sent by the master, the device responds with
its address, and it is the lowest address currently asserting the ALERT/RDY bus line. This bit serves no
function on the ADS1013.
0 : Non-latching comparator (default)
1 : Latching comparator
Bits [1:0] COMP_QUE: Comparator queue and disable (ADS1014 and ADS1015 only)
These bits perform two functions. When set to '11', they disable the comparator function and put the
ALERT/RDY pin into a high state. When set to any other value, they control the number of successive
conversions exceeding the upper or lower thresholds required before asserting the ALERT/RDY pin. They
serve no function on the ADS1013.
00 : Assert after one conversion
01 : Assert after two conversions
10 : Assert after four conversions
11 : Disable comparator (default)
(1) This parameter expresses the full-scale range of the ADC scaling. In no event should more than VDD + 0.3V be applied to this device.
16 Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): ADS1013 ADS1014 ADS1015