Datasheet
www.ti.com
Electrical Characteristics
(1)
SN74AVCBH324245
32-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
SCES550B – FEBRUARY 2004 – REVISED JUNE 2005
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS V
CCA
V
CCB
MIN TYP
(2)
MAX UNIT
I
OH
= –100 µ A, V
I
= V
IH
1.4 V to 3.6 V 1.4 V to 3.6 V V
CCO
– 0.2
I
OH
= –2 mA, V
I
= V
IH
1.4 V 1.4 V 1.05
V
OH
I
OH
= –4 mA, V
I
= V
IH
1.65 V 1.65 V 1.2 V
I
OH
= –8 mA, V
I
= V
IH
2.3 V 2.3 V 1.75
I
OH
= –12 mA, V
I
= V
IH
3 V 3 V 2.3
I
OH
= 100 µ A, V
I
= V
IL
1.4 V to 3.6 V 1.4 V to 3.6 V 0.2
I
OH
= 2 mA, V
I
= V
IL
1.4 V 1.4 V 0.35
V
OL
I
OH
= 4 mA, V
I
= V
IL
1.65 V 1.65 V 0.45 V
I
OH
= 8 mA, V
I
= V
IL
2.3 V 2.3 V 0.55
I
OH
= 12 mA, V
I
= V
IL
3 V 3 V 0.7
I
OHD
= –6 mA, V
I
= V
IH
1.4 V 1.4 V 1.05
I
OHD
= –9 mA, V
I
= V
IH
1.65 V 1.65 V 1.2
V
OH
V
I
OHD
= –15 mA, V
I
= V
IH
2.3 V 2.3 V 1.75
I
OHD
= –24 mA, V
I
= V
IH
3 V 3 V 2.3
I
OHD
= 6 mA, V
I
= V
IL
1.4 V 1.4 V 0.35
I
OHD
= 9 mA, V
I
= V
IL
1.65 V 1.65 V 0.45
V
OL
V
I
OHD
= 15 mA, V
I
= V
IL
2.3 V 2.3 V 0.55
I
OHD
= 24 mA, V
I
= V
IL
3 V 3 V 0.7
I
I
Control inputs V
I
= V
CCB
or GND 1.4 V to 3.6 V 3.6 V ±2.5 µ A
V
I
= 0.49 V 1.4 V 1.4 V 11
V
I
= 0.57 V 1.65 V 1.65 V 25
I
BHL
(3)
µ A
V
I
= 0.7 V 2.3 V 2.3 V 45
V
I
= 0.8 V 3 V 3 V 75
V
I
= 0.49 V 1.4 V 1.4 V –11
V
I
= 1.07 V 1.65 V 1.65 V –25
I
BHH
(4)
µ A
V
I
= 1.7 V 2.3 V 2.3 V –45
V
I
= 2 V 3 V 3 V –75
1.6 V 1.6 V 100
1.95 V 1.95 V 200
I
BHLO
(5)
V
I
= 0 to V
CC
µ A
2.7 V 2.7 V 300
3.6 V 3.6 V 525
1.6 V 1.6 V –100
1.95 V 1.95 V –200
I
BHHO
(6)
V
I
= 0 to V
CC
µ A
2.7 V 2.7 V –300
3.6 V 3.6 V –525
(1) V
CCO
is the V
CC
associated with the output port.
(2) All typical values are at T
A
= 25°C.
(3) The bus-hold circuit can sink at least the minimum low sustaining current at V
IL
max. I
BHL
should be measured after lowering V
IN
to GND
and then raising it to V
IL
max.
(4) The bus-hold circuit can source at least the minimum high sustaining current at V
IH
min. I
BHH
should be measured after raising V
IN
to
V
CC
and then lowering it to V
IH
min.
(5) An external driver must source at least I
BHLO
to switch this node from low to high.
(6) An external driver must sink at least I
BHHO
to switch this node from high to low.
6