Installation Manual
Table Of Contents
- Safety summary
- About this manual
- Introduction to EXPLORER 323
- To install the system
- To get started
- Before you start
- To switch on the EXPLORER 323
- To connect to the LAN interface
- To connect your WLAN-enabled device
- The EXPLORER Connect app
- To access the web interface
- To enter the SIM PIN for the terminal
- To register with the BGAN network
- Mounting calibration
- To start and stop data connections
- To make phone calls over BGAN
- To use the EXPLORER 323
- Configuration with web interface
- The web interface
- To control data connections from web interface
- To set up your data connection packages
- Multiple data connections
- Status information
- The Control panel
- To use the logs
- Terminal settings
- To set up the interfaces
- To manage VoIP phones or smartphones (Not M2M)
- Advanced LAN
- To manage connected devices (Traffic control)
- To set up tracking and location reporting
- Support features
- Advanced settings
- Passwords
- To set up user permissions
- To restore factory settings
- SIM PIN for BGAN
- To save or load a configuration
- Connection watchdog (Link monitoring)
- Terminal watchdog
- Data limits
- Call charges
- Remote management
- Remote control of tracking
- Power save
- To configure data connection types and filters
- Help desk
- Reset button
- Security
- To enter the SIM PIN in the web interface
- Maintenance and troubleshooting
- Specifications
- Command reference
- Conformity
- Glossary
- Index
Chapter 2: To install the system
98-169085-B To connect cables 13
4. Connect a computer, either with the Ethernet interface as described in the next section, or
via WLAN as described in To connect your WLAN-enabled device on page 19.
5. On the connected computer, open your browser and access the web interface by typing
the local IP address in the address bar (default IP address: 192.168.0.1).
6. Select Advanced > Power control and enable the Remote on/off function as
described in Power save on page 90.
7. Verify the Remote on/off function by starting and stopping the ignition of the vehicle and
observing the EXPLORER 323 switching on and off.
The Power control pin (Remote on/off signal)
The Power control pin is connected to the blue Remote on/off wire in the EXPLORER 323 cable.
See To connect Ignition on page 12.
Connection example for the Power control pin:
• If you have configured the input to be Active low (default):
To deactivate: Connect the Power control pin (blue wire) to V+ (High: 2.8 - 32 VDC).
To activate: Connect the Power control pin (blue wire) to GND (Low: 0 - 0.8 VDC).
• If you have configured the input to be Active high:
To deactivate: Connect the Power control pin (blue wire) to GND (Low: 0 - 0.8 VDC).
To activate: Connect the Power control pin (blue wire) to V+ (High: 2.8 - 32 VDC).
Important
The Power control pin, pin C in the EXPLORER 323 connector, is internally pulled
down. This means that when it is not connected, it will always be in Low
state. However, the state of the Power control pin is only used if Remote
on/off is selected as power save mode, or if Idle power save mode is selected
with the wake-up function Power control pin enabled.
V‐,PinB
Remoteon/off,PinC
V+
V+
V+ V+
Active
Active
Inactive
Inactive
ActiveLow
Example
ActiveHigh
Example
V+,PinA
V‐
V‐,PinB
Remoteon/off,PinC
V+,PinA
V‐
V‐,PinB
Remoteon/off,PinC
V+,PinA
V‐
V‐,PinB
Remoteon/off,PinC
V+,PinA
V‐