User's Manual

PRODUCTPREVIEW
11
CC2650MOD
www.ti.com SWRS187 –AUGUST 2016
Submit Documentation Feedback
Product Folder Links: CC2650MOD
SpecificationsCopyright © 2016, Texas Instruments Incorporated
(1) Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2
(Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan)
5.8 1-Mbps GFSK (Bluetooth low energy) – TX
RF performance is specified in a single ended 50-Ω reference plane at the antenna feeding point with T
c
= 25°C,
V
DDS
= 3.0 V, f
RF
= 2440 MHz, unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Output power, highest setting 5 dBm
Output power, lowest setting –21 dBm
Spurious emission conducted
measurement
(1)
f < 1 GHz, outside restricted bands –43 dBm
f < 1 GHz, restricted bands ETSI –65 dBm
f < 1 GHz, restricted bands FCC –76 dBm
f > 1 GHz, including harmonics –46 dBm
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
(3) Excluding one exception at F
wanted
/ 2, per Bluetooth Specification.
5.9 2-Mbps GFSK (Bluetooth low energy) – RX
RF performance is specified in a single ended 50-Ω reference plane at the antenna feeding point with T
c
= 25°C,
V
DDS
= 3.0 V, f
RF
= 2440 MHz, unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Receiver sensitivity
Differential mode. Measured at the CC2650EM-5XD
SMA connector, BER = 10
–3
–91.7 dBm
Receiver saturation
Differential mode. Measured at the CC2650EM-5XD
SMA connector, BER = 10
–3
4 dBm
Frequency error tolerance
Difference between the incoming carrier frequency
and the internally generated carrier frequency
–300 500 kHz
Data rate error tolerance
Difference between incoming data rate and the
internally generated data rate
–1000 1000 ppm
Co-channel rejection
(1)
Wanted signal at –67 dBm, modulated interferer in
channel,
BER = 10
–3
–7 dB
Selectivity, ±2 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at
±2 MHz,
Image frequency is at –2 MHz
BER = 10
–3
8 / 4
(2)
dB
Selectivity, ±4 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at
±4 MHz,
BER = 10
–3
31 / 26
(2)
dB
Selectivity, ±6 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at
±6 MHz,
BER = 10
–3
37 / 38
(2)
dB
Alternate channel rejection, ±7
MHz
(1)
Wanted signal at –67 dBm, modulated interferer at ≥
±7 MHz, BER = 10
–3
37 / 36
(2)
dB
Selectivity, Image frequency
(1)
Wanted signal at –67 dBm, modulated interferer at
image frequency,
BER = 10
–3
4 dB
Selectivity, Image frequency
±2 MHz
(1)
Note that Image frequency + 2 MHz is the Co-
channel. Wanted signal at –67 dBm, modulated
interferer at ±2 MHz from image frequency,
BER = 10
–3
–7 / 26
(2)
dB
Out-of-band blocking
(3)
30 MHz to 2000 MHz –33 dBm
Out-of-band blocking 2003 MHz to 2399 MHz –15 dBm
Out-of-band blocking 2484 MHz to 2997 MHz –12 dBm
Out-of-band blocking 3000 MHz to 12.75 GHz –10 dBm
Intermodulation
Wanted signal at 2402 MHz, –64 dBm. Two
interferers at 2405 and 2408 MHz respectively, at
the given power level
–45 dBm