User's Manual

PRODUCTPREVIEW
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCT PREVIEW Information. Product in design phase of
development. Subject to change or discontinuance without notice.
CC2650MOD
SWRS187 –AUGUST 2016
CC2650MOD SimpleLink™ Multistandard Wireless MCU Module
1 Device Overview
1
1.1 Features
1
• Microcontroller
– Powerful ARM
®
Cortex
®
-M3
– EEMBC CoreMark
®
Score: 142
– Up to 48-MHz Clock Speed
– 128KB of In-System Programmable Flash
– 8KB of SRAM for Cache
– 20KB of Ultra-Low Leakage SRAM
– 2-Pin cJTAG and JTAG Debugging
– Supports Over-The-Air Upgrade (OTA)
• Ultra-Low Power Sensor Controller
– Can Run Autonomous From the Rest of the
System
– 16-Bit Architecture
– 2KB of Ultra-Low Leakage SRAM for Code and
Data
• Efficient Code Size Architecture, Placing Drivers,
Bluetooth
®
low energy Controller, IEEE 802.15.4
MAC, and Bootloader in ROM
• Integrated Antenna
• Peripherals
– All Digital Peripheral Pins Can Be Routed to
Any GPIO
– Four General-Purpose Timer Modules (8 × 16-
Bit or 4 × 32-Bit Timer, PWM Each)
– 12-Bit ADC, 200-ksamples/s, 8-Channel Analog
MUX
– Continuous Time Comparator
– Ultra-Low Power Analog Comparator
– Programmable Current Source
– UART
– 2 × SSI (SPI, MICROWIRE, TI)
– I
2
C
– I2S
– Real-Time Clock (RTC)
– AES-128 Security Module
– True Random Number Generator (TRNG)
– 15 GPIOs
– Support for Eight Capacitive Sensing Buttons
– Integrated Temperature Sensor
• External System
– On-Chip internal DC-DC Converter
– No External Components Needed, Only Supply
Voltage
– Version With CC2592 Range Extender Available
• Low Power
– Wide Supply Voltage Range
• Operation from 1.8 to 3.8 V
– Active-Mode RX: 6.1 mA
– Active-Mode TX at 0 dBm: 6.1 mA
– Active-Mode TX at +5 dBm: 9.1 mA
– Active-Mode MCU: 61 µA/MHz
– Active-Mode MCU: 48.5 CoreMark/mA
– Active-Mode Sensor Controller: 8.2 µA/MHz
– Standby: 1 µA (RTC Running and RAM/CPU
Retention)
– Shutdown: 100 nA (Wake Up on External
Events)
• RF Section
– 2.4-GHz RF Transceiver Compatible With
Bluetooth low energy (BLE) 4.1 Specification
and IEEE 802.15.4 PHY and MAC
– Excellent Receiver Sensitivity (–97 dBm for
Bluetooth low energy and –100 dBm for
802.15.4), Selectivity, and Blocking
Performance
– Programmable Output Power up to +5 dBm
– Integrated Antenna
– Pre-Certified for Compliance With Worldwide
Radio Frequency Regulations
• ETSI (Europe)
• IC (Canada)
• FCC (USA)
• ARIB STD-T66 (Japan)
• Tools and Development Environment
– Full-Feature and Low-Cost Development Kits
– Multiple Reference Designs for Different RF
Configurations
– Packet Sniffer PC Software
– Sensor Controller Studio
– SmartRF™ Studio
– SmartRF Flash Programmer 2
– IAR Embedded Workbench
®
for ARM
– Code Composer Studio™