Owner manual

ManualsBrandsTerraWave ManualsEquipment802.11n MIMO Site Survey Battery Pack

TerraWave Solutions®

MIMO Site Survey Battery Pack (Part # TW-SSBP-007)

Instructions For Use

Version 2.0 - Page 1

www.terrawave.com Email: sales@terrawave.com Phone: 210-375-8482 or 800-851-4965 10521 Gulfdale, San Antonio, TX 78216

Standard Shipping Contents of the TW-SSBP-007:

1 qty Site Survey Battery Pack (Diagram 1)

1 qty Charger (Diagram 2)

1 qty RJ-45 Red (802.3af) POE Cable (Diagram 3)

1 qty 2’ 56 Volt Power Cord (Diagram 4)

1 qty 20’ 56 Volt Power Cord (Diagram 4)

1 qty Bag of mounting plate fastening screws

Diagram 1: Site Survey Battery Pack

Summary of content (8 pages)

PAGE 1
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Standard Shipping Contents of the TW-SSBP-007: 1 qty Site Survey Battery Pack (Diagram 1) 1 qty Charger (Diagram 2) 1 qty RJ-45 Red (802.3af) POE Cable (Diagram 3) 1 qty 2’ 56 Volt Power Cord (Diagram 4) 1 qty 20’ 56 Volt Power Cord (Diagram 4) 1 qty Bag of mounting plate fastening screws Diagram 1: Site Survey Battery Pack Version 2.0 - Page 1 www.terrawave.com Email: sales@terrawave.
PAGE 2
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Dimensions of Battery Pack: Approximate Weight: 8 lbs. Version 2.0 - Page 2 www.terrawave.com Email: sales@terrawave.
PAGE 3
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Diagram 2: Charger Diagram 3: RJ-45 Red (802.3af) POE Cable This cable is intended for use for all access points that are 802.3af POE compliant. Version 2.0 - Page 3 www.terrawave.com Email: sales@terrawave.
PAGE 4
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Diagram 4: 56v power cable w/barrel connector AP1252 This cable is intended for use with the Cisco AP1252. Diagram 5: 56v power cable w/barrel connector AP1252 This cable is intended for use with the Cisco AP1252. Diagram 6: 48v POE for patch cable This cable is intended for use with 802.3af complaint Access Points only. Version 2.0 - Page 4 www.terrawave.com Email: sales@terrawave.
PAGE 5
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Diagram 7: Access Point Mounting Holes on Lid of Site Survey Battery Pack C1 C2 S2 P1 C2 S1 S1 P1 C1 P1L C1 S2 C2 C2 C1 S1L Front Edge (Above switches) C1, C2, P1, S2 = 8-32 threaded S1L, P1L = 10-32 threaded Hole Usage Chart: Hole Screws to Use C1 2 qty 8-32 Pan-head x 3/8” long C2 S1 S1L S2 P1 P1L 4 qty 8-32 Flat-head x 3/8” long 2 qty 6-32 Pan-head x 3/8” long 1 qty 10-32 Locking Post 2 qty 8-32 Pan
PAGE 6
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Key Points to Understand: 1. Site Survey Battery Pack should power any access point or bridge for at least 6-8 hours given that the Site Survey Battery Pack has been fully charged. 2. The POE port is designed to power 48 Volt POE access points only. 3.
PAGE 7
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use Charging Instructions: 1. The Site Survey Battery Pack must be charged before each use. It is recommended to charge the Site Survey Battery Pack immediately upon receipt and before any expected use. 2. Turn the Master Battery On/Off switch to the “On” position for charging to commence. 3. Turn the switch (labeled Switch in Diagram 1) to the “Charge / Off” or LEFT position. 4.
PAGE 8
TerraWave Solutions® MIMO Site Survey Battery Pack (Part # TW-SSBP-007) Instructions For Use CAUTION! The aforementioned instructions allow the use of both radios with the AP powered by the 48V PoE connection (see instructions below). This method is for site survey purposes only. DO NOT use an AP in a production environment with these settings. Using this method in a production environment will likely cause damage to the AP and / or switch. B.) The battery pack will support the 802.