Operation and maintenance manual

3
Section 000-0000
SM 2110 Rev 4 03-05
General Information - Technical Data
Steering
Hydrostatic power steering by two double-acting,
cushioned steering cylinders. Actuating pressure for
steering operation is supplied by the main hydraulic gear
pump.
Emergency steering pressure is provided by a ground
driven pump mounted on the transmission. An indicator
lamp signals should the emergency system activate.
Conforms to SAE J53.
System pressure ................................. 206 bar (3000 lbf/in²)
Steering Angle (left and right) ......................................... 45°
Lock to Lock Turns, steering wheel .................................... 4
Clearance Turning Diameter (SAE) ................ 19.5 m (64 ft)
Body
Two single-stage, double-acting hoist cylinders, cushioned
at both ends of stroke. Electro servo assisted hoist control.
Actuating pressure for body hoist is supplied by the main
hydraulic gear pump.
System pressure ................................. 172 bar (2500 lbf/in²)
Control Valve .......................... Pilot Operated, Open Centre
Body Raise Time (loaded) ......................................... 16 sec
Body Lower Time (power down) ................................12 sec
ELECTRICAL SYSTEM
Type ............................................. 24 volt, Negative Ground.
Battery ......... Two, 12 Volt, 175 Ah each, Maintenance Free
Accessories ............................................................... 24 Volt
Alternator ..................................................................70 Amp
BODY
All welded construction, fabricated from high hardness
(min. 360 BHN) 1 000 MPa (145 000 lbf/in²) yield strength
steel. 25° tail chute angle provides good load retention
without tailgate.
Plate Thicknesses:
Floor and Tailchute ................................... 15.0 mm (0.59 in)
Sides ......................................................... 12.0 mm (0.47 in)
Front .......................................................... 10.0 mm (0.39 in)
Volume:
Struck (SAE) ............................................ 17.0 m³ (22.2 yd³)
Heaped 2:1 (SAE) ................................... 22.0 m³ (28.8 yd³)
* * * *
SERVICE CAPACITIES
Fuel tank .......................................... 463 litres (122 US gal)
Hydraulic System
(Steering, Braking & Body) ................ 209 litres (55 US gal)
Brake Cooling System .................... 199 litres (52.6 US gal)
Cooling System ................................ 80 litres (21.1 US gal)
Engine Crankcase (with filters) .......... 37 litres (9.8 US gal)
Transmission (with filters) ................. 56 litres (14.8 US gal)
Differential - Dana (Front) ................ 37.5 litres (9.9 US gal)
Differential - Dana (Centre) ................. 38 litres (10 US gal)
Differential - Dana (Rear) ................ 31.5 litres (8.3 US gal)
Planetaries - Dana ............................ 8.5 litres (2.2 US gal)
Driveshaft Bearings ........................... 1.5 litres (0.4 US gal)
Air Conditioning Compressor .... 0.125 litres (0.033 US gal)
VEHICLE WEIGHTS
Standard Vehicle kg lb
Net Distribution
Front Axle 15 275 33 675
Centre Axle 7 750 17 085
Rear Axle 7 705 16 985
Net Weight 30 730 67 745
Payload 36 500 80 470
Gross Distribution
Front Axle 20 170 44 465
Centre Axle 23 530 51 875
Rear Axle 23 530 51 875
Gross Weight 67 230 148 215
Bare Chassis 24 670 54 390
Body 5 400 11 905
Body Hoists (pair) 660 1 455
Ground Pressures
At 15% sinkage of unloaded radius and specified weights
29,5 R25 Net Loaded
Front
102 kPa (14.8 psi) 135 kPa (19.6 psi)
Rear 52 kPa (7.5 psi) 158 kPa (22.9 psi)