TR-UM006 Teri Bar code Scanner User Manual Model No.: 8100 / HW0002 / HW0008 An asterisk next to an option Indicates the default setting. Scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this manual. Note: If there Is no further setting command within 20 seconds, the scanner well automatically exit the setting mode.
Contents Factory Reset Working Mode Communication Mods. 2,46 Pairing Setting. Wireless 2.4G Pairing Step: Bluetooth Bluetooth HID Paling Steps. Bluetooth STOPPABLE Pairing Steps. Bluetooth HID Transmission Speed. Bluetooth Name Setup Sleep Time Setting. 10S System HID Virtual Keyboard Setting Terminator Keyboard Language Setting. Upper/Lower Case Symbology Hidden Character GS Replacement, GS Replacement. Suffixation Setup. Hide Prefix/Suffix.. Appendix ASCII Character Form.
Factory Reset CIE m Factory Reset You may scan this bar code, when: 1. The bar code scanner Is set Incorrectly, such as when the bar code cannot be scanned. 2. The user has forgotten the previous setting or does not want to keep the previous setting. 3. The bar code scanner was set to use some functions which are no longer needed. VIAL [EEE 5 Battery Level Version No. Working Mode Instant Upload Mode: Under instant upload mode, the data readout is uploaded to the computer directly.
Communication Mode: EEE oh HEE a [Ee ode ELE Bluetooth SPP Mode Bluetooth BLE Mode Note: The Bluetooth SPP mode and BLE mode can only be used after downloading or developing corresponding software. 2.46 Pairing Setting: 1. Wireless 2.4G Pairing Steps (USB Receiver pairing) Step 1: Mode” Step 2: Scan “Compulsory Paar with Dongle” to enter pairing mode, the left blue light flashes rapidly. Step 3: Plug in the dongle. Pairing is successful when buzzer sounds “dee” and the right blue light is turns on.
mam EEE ws Bl Bluetooth Hil Mode Compulsory Pair with Bluetooth Note: When entering pairing mode, if the user presses the button twice or the device is not detected in more than 1 minute, pairing fails. While using the Bluetooth function, the user can press the button for 8 seconds to enter the pairing mode more quickly.
= Low Super Low Bluetooth Name Setup Use following steps to name the Bluetooth HID, SPP or BLE For example: Name the Bluetooth: Scanner Step 1: Scan “Customize Bluetooth Name” code Step 2: Make and scan the Bluetooth Name code 3 [x] 21 EEE b i Customize Example: Bluetooth Name Bluetooth Name Scanner After setting: The Bluetooth HID name will show as: Scanner HID The Bluetooth SPP name will show as: Scanner SPP The Bluetooth BLE name will show as: Scanner BLE Note: a) The maximum length of the name Is 16 byt
Vibration Setting Not: Ti re ct stein madam Sleep Time Setting WEE [Ellie Es a 2g EEE elatedly 108 System HID Virtual Keyboard Setting EEE EE a i “Double-click to show 10S “Double-click to show 10S Keyboard (HID Keyboard (HID Mode) OFF Terminator Setting ‘Add Carriage Return (Oxford* Add Linefeed (0x08) CIE, Add Cartage Retum+Linefeed (CXOD,040A) None 05
Keyboard Language Setting Different languages have different keyboard positions and symbols. The scanner can be ritualized Into different keyboard forms. according to actual requirements. The keyboard position setting is applied to “HID Communication Port Mode” and “American English Keyboard” Is the default.
iE EEE All Lower Cage Inverse Note: These settings can only be valid In standard keyboard Input mode and keyboard emulation input control characters mode. Symbology UPC-At NAE-13 I CTT Bar codes Of i aE UNIT Inverted Bar codes Setting ORIGINATE BERET Read Inverted Bar code* Read Both Normal and Inverted Bar code LT UPC-A OFF URETER ROE UPC-A Check Digits ON% UPC-A Check Digits OFF UPC-A code consists of 12 digits and the 12th of which Is the check digit.
UPC-E code consists of 8 di ions and the 8th of which is the check digit. The check digit Is used to check the validity of the whole 8 da The check digit is transmitted by default. ung ong “ing nm NAE-13 OFF Transmission to ISBN MINIATURE Fain Transmission FISSION Transmission to ISBN OFF* Transmission to SINS SHANNON DRE Transmission to SINS ON Transmission to SINS OFF* UPC/EAN/JAN Additional Digits Setting Additional digit means the 2 or 5 digits which are added after the normal digits.
Code 39 CO NAR Code 39 Full ASCII ON Code 39 Full ASCII OFF* HL Check Digits OFF NAT Hm MOD 43 Checked ON MOD 43 Checked ON and and Transmission ON Transmission OFF* Code 32 a TT Note: When the “Code scanning of Code 39 will be affected. Only when Code 39 without check digits Is on can Code Pharmaceutical be scanned.
Industrial GS1 Data Bar CLT Ct GS1 Data Bar Lime ass: Limited) TOT G51 Data Bar LAIR om UL QR Code ITT TT Micro QR Code TWEETER NERD Micro QR Code ON* Micro QR Code OFF Data Matrix ITS Ee Data Matrix ON¥ Data Matrix OFF PDF 417 QUORUM OUTRAN PDF 417 ON* PDF 417 OFF Micro PDF 417 (UF EAT EE Micro PDF 417 ON* Micro PDF 417 OFF 10
Hidden Character GS Replacement This function can use the hidden character GS in place of other characters to display In the device. When hidden character GS is needed fo be displayed, the GS can be set to replace the 1D of ASCII form. GS Replacement Step: Scan “GS Replacement” Replacement ON RL OFF Step: Search Character Form” to find the bar code of the character to be replaced. For example; Replace the GS character with the displayable character |.
[El] Add Prefix ‘Exit Setting Suffix Setup Step: Sean "Add Suffix” Step: Search the “ASCII Character Form” te find the bar codes for the suffix and scan them in order. (The user has to scan the corresponding 0-3 character set when the content of the ESC Is needed). mE Add Suffix For example: Add suffix “XYZ” to the bar code “ABC123", to get the result “ABC123XYZ". Step: Scan "Add Suffix” Step: Search the "ASCII Character Form” to find the bar codes for “X", “Z" and scan them In order.
Step: Scan the following bar codes In accordance with the number of digits to be hidden. Hide 1 Digits. Hide 2 Digits Hide 3 Digits Ei Digits. Clear the Hidden Prefix/Suffix Step: Scan “Hide Prefix” or “Hide Suffix” Step: Scan “Exit Setting” EEE FE Hak ER To mim Depreciate ~ Sextet ~~ Hide Suffix Exit Setting Appendix-ASCII Character Form The Prefix and Suffix form can be divided into 2 parts: Control Character Form and Displayable Character Form.
sje |; Jom | we oz) [{HONING vase rm CAN | F11 F3 Cicatrix Alt+024 NEE wre (re (ow | ans [ITI sm wu [es owe |e] [IIH ESC | ESC F§ cir | At+027 HEN I rs Jams |r un | wos | INI os (mas ro own | avo | [JILIN ws [wu |; phone | avocado [EQUINE us NULL F10 Cirri_ A031 I [RW 2D Setting 2D Ratting 2D Setting character) “C2 character | “27M | Character Code in| EGE [ORO] Space ole tw i 16
EL EGE i pd Sam Zhe ih ihn Si a Ela: | mgm im Age ERE i a z IRE ali Cif: Aad SEE | a hed B 19
If you need any product support, contact our customer service email, where you will get professional product support. Important Notice: Please attach your Amazon Order Number and Product Order Number in the email. Official Customer Service Mall Address: service-us@ service-EU@ service-UK@ If you would lke to meal more about our brand or need complete digital user manual, please visit our official website via the links below or by scanning the given QR code.
