Vehicle intelligent terminal MV03 User Manual
Disclaimer This manual is applicable to the onboard intelligent video terminal.This manual may contain technical inaccuracies or misprints.The contents of this manual will be updated irregularly without prior notice.The updated content will be added in the new version of this manual, we will improve or update at any time.The products or procedures described in this manual.If the description of the product in the manual is inconsistent with the real product, the real product shall prevail.
adopts modular design, which has the characteristics of high reliability, flexible installation and convenient maintenance. Working flow DSM camera Beidou/GPS Monitor ADAS camera 3/4G Transmission Local Video and Playback Function: Resolution 720P Network function: support real-time transmission of 4G network, remote alarm, parameter setting and over the air upgrade. Equipment Upgrade: Support local upgrade and OTA upgrades/remote upgrade.
Product Specification DSM module parameters DVR Hardware Parameter Parameter Types Camera Resolution Focal length Aperture number Perspective Working Distance Working Condition Detection of facial patterns Scope of detection Fatigue accuracy Distraction Accuracy Smoking Accuracy Calling Accuracy Project System Video Input/Output Requirements Remarks AHD720p Default 3.6 mm F2.
Video Input/Output Audio Input/Output Video Audio Coding DVR Hardware Parameter Videotape Video Display Single Screen,Double Screen Synchronize Channel display Video Compression H.264 Main profile Audio Input 1 CH Audio Input Audio Bit Rate 40Kbit/s Audio Output 1 CH Audio Output Video Coding Resolution Analog HD 720P Dual-Stream Video Mainstream video, sub-stream 4G network transmission Storage Medium Main Memory:TF Card,Single card support max.
DVR Hardware Parameter ADAS Parameters Satellite Positioning Tracking sensitivity -159dBm Communication External interface 2G/3G/4G Communication interface all Netcom USB 2.0 x 2,RS232 x 1,RS48S x 1 Network interface WIFI,RJ45 Interfacex1,10M/100M Audio 8Ω/1W Power input DC:+9V ~ +36V Power Output +12V/1A Structure Working Current Size Less than 12w 119.5*97*40.4mm TF card Supports Class 4-10, FAT32 format and 128G single expenses.
Environmental characteristics Interface definition Applicable environment Operating temperature Storage temperature Relative humidity 16 Pin Extension Cable Interface Detailed Parameters -30℃ ~ +70℃ -40℃ ~ +85℃ 5% ~ 95% (no frost) Remarks No.
DSM Camera Interface Interface definition ADAS Camera Interface USB Interface Monitor Interface 1 Red DSM_AHD_VCC 2 Blue DSM _Audio_IN 3 Yellow DSM _AHD_IN 4 Black GND 5 White SP+ 6 Green SP- 7 Purple LED 1 Red 12v Output 2 Black GND 3 Blue IO_Reserved 4 Green AHD_IN 1 Black GND 2 Green D+ 3 White D- 4 Red VCC 1 HDMI interface AVOUT 7 Pin DSM aviation head interface,DSM signal input.
Front Panel Interface Name Description USB Interface Micro USB Serial Port communication,Software Upgrade and Video Export SIM Slot Storage Card1 Micro SIM TF Card SIM card socket for SIM card insertion TF card socket, mainly used for the storage of audio and video files and upgrade for DSM and ADAS Standard Accessories Accessories Requirement Optional Accessories No. Name Qty No.
Function Description No. Function Status Function Description 1 Boot self-check or Post Support 1. Indicate the relevant working status through the equipment indicator. 2 Real-time location upload Support 1. To upload device real-time location information to the platform at a certain time interval (default 10 seconds) 3 Alarm broadcast Support 1.
6 Blind area re-transmission Support 1. The equipment automatically stores the position data in the place of signal weakly and automatically transmits the position information while there is a signal. 7 Fatigue Warning Support 8 Distraction Warning Support 9 Smoking Warning Support When the device works normally: 1. when the vehicle speed is more than 30 km/ h during the running, once the DSM camera detects driver continuous 2 seconds smoking state, and the alarm is generated; 2.
2. When the alarm is generated, the device transmits the calling driving alarm information through 4G module, and the alarm information includes alarm status and picture information to the monitoring platform. 11 L a n e D e p a r t u r e Support Warning (LCW) 12 Forward Collision Support Warning (FCW) 13 APP Debugging 1.
Equipment Installation 1. Notices: 1). Comply with all electronic product specifications, vehicle and other connecting equipment requirements when installing and operating equipment. 2). Power supply and ground: a) Use DC power supply for video recorder. Please pay attention to the positive and negative polarity when connecting power supply. b) The input voltage range of the DVR is 9 V-36 V. Do not connect to the power supply beyond this range.
3). Humidity requirements: a) Install equipment in a dry environment to avoid moisture, dripping, water spray, etc. Do not install the device in a place where it may accumulate water or a wet place where liquid will drip. b) Do not touch the device with wet hands, or touch the device while standing in the water or in contact with other water sources, because there is a risk of electric shock. 2. Installation DVR Main device installation 1).
Installation of DSM and ADAS cameras 1. Installation position The DMS camera needs to be installed under the left side of the A pillar of the vehicle as follow: and the ADAS camera needs to be installed on the front windshield. 2. Distance requirement The distance between driver’s head to camera is within 50cm-120cm. 3. Installation mode Glue the ADAS camera to the front windshield and fix the DSM camera at the car body by screw(or glue the DSM camera,it depends on the camera type).
1) Install an application“Calibrator”to android system phone. (This app is developed by our company, only works on android system phone). 2) Open the Calibrator, click the right bottom button “Mine” on your phone, select the server IP 192.168.43.1 as shown below: 3) After the device is started, the mobile phone search WIFI which is called "TS-AP-Equipment-xxxxx",enter password 123456789 to connect the device.
2. DSM Calibration 1) Click DSM calibration, it will take you to the camera position correction page, DSM is recommended to be installed at the left front of the driver, under the A pillar. ( Different type of vehicle has different installation position). Adjust the camera position slightly make sure your face is at the center of the screen inside the blue rectangle frame, you might get “calibration is successful” notification on the screen.
3. ADAS Calibration 1) Click ADAS Calibration, you will get Adjust ADAS camera position page , adjust the camera angle to locate the horizon line between the two yellow guiding lines, make sure the middle line coincides with horizon line, go to the next step. (Measure the height from the ADAS camera to the ground. Find an equal height reference 3 to 5 meters in front of the vehicle, make sure the green line of the debug screen coincides with it by adjusting camera lens.
2) Calibrate vanishing point position, move the blue cross so that the center point of the cross coincides with horizon line. You can use the four direction arrow to adjust slightly, and then go to the next step. 3) Set the parameters information according to your vehicle. After setting, click Finish.
4. Parameter setting 1) Open the debugging assistant app tsAide. 2) Connect to the hotspot of the device , the hotspot name is TS-AP-SN, and the password is 123456789; then return to the interface on the phone, friendly reminder: please turning on all permissions during the installation process. 3) After connection successfully, return to the main interface.
4) Click Device setting at the bottom of the screen, it will take you to next page, you can set the debugging mode, DSM alarm parameters, ADAS alarm parameters, terminal parameters, and Manager parameters. When setting terminal parameters, the mobile phone number must be 12 digits. If there is only 11 digits, please add 0 in front. This No. is the ID of this device on the server. Please contact us before you change it.
5. Wiring connection method: 1) Power cable connection method: Open the cover of the car safety box and measure the voltage with a multimeter. As shown in the figure, the range of the voltage of the car power supply is between DC11V and 13V. (The multimeter red pen is positive and the black pen is negative.) Find out the positive and negative poles of the power supply.
2) Install GPS antenna Make sure you don't switch on the equipment power first! a) The arc side of the GPS antenna face the sky, and there is no metal shielding and electromagnetic shielding above. b) In order to receive good signal, the flat bottom of the GPS antenna should be installed as flat as possible, and the angle should not exceed 45 degrees. c) The wiring is as concealed as possible: first, it is beautiful; second, it is to prevent unintentional or intentional damage.
6. Appendix: 1) Common Questions and Answers Q:What should I do if the product has problems that I can't handle? A:please record the product model and software version number, submit detailed problem description, phenomenon, picture to our technical support engineer for analysis. The more detailed you describe, the more convenient it will be for us to analyze and process.
2) Troubleshooting:The device is not online a) Check whether the device terminal number is correct or not. Enter 12 digits terminal number according to the platform, set IP and port correct correctly. b) Check whether the 4G signal of the device is normal. If there is no signal, change a place and look at the signal. If there is no 4G signal, there may be a problem with the SIM card. c) Check the information on the platform.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
