User's Manual
56019201
Pag
e
© 2000 Telular Corporation
29
A2.1 Setup Programming Parameters
Parameter Description
Cellular System A or B
Program Location 32
The cellular network system through which the Telguard radio is authorized to place calls to the central station.
System B is the wireline system (usually operated by the local telephone company) and System A is the non-
wireline system (usually operated by the telephone company's competitor). 1=A, 2=B.
C/C Reporting Format
Program Location 33
This format must be the same format that the C/C is programmed to use when communicating with the central
station over Telco. The programmed selection tells the Telguard how to digitally encode alarm messages from the
C/C to the central station over the cellular network control channels.
1=4 + 2 Pulse 40 PPS 2300 Ack (Double Round) Non-Extended
2=4 + 2 Pulse 20 PPS 2300 Ack (Double Round) Non-Extended
3=4 + 2 Pulse 20 PPS 1400 Ack (Double Round) Non-Extended
4=3 + 1 Pulse 40 PPS 2300 Ack (Double Round) Non-Extended
5=3 + 1 Pulse 20 PPS 2300 Ack (Double Round) Non-Extended
6=3 + 1 Pulse 10 PPS 1400 Ack (Double Round) Non-Extended
7=Radionics Modem IIE or 3A
2
8=Contact ID (Ademco)
STC Trip Output Reporting
Program Location 51
Telguard has the capability to supervise proper operation of both power supplies (AC & DC) and proper
operation of both paths of communication (Telco and Cellular) to the central station. Should a condition occur that
prevents Telguard from operating properly, the condition if programmed, will cause the supervisory trip output
(STC) to trip the C/C's 24-hour zone forcing the C/C to communicate the "Telguard
S
ystem
T
rouble
C
ondition" to
the central station.
Enter the
Sum Total
of STC events that you wish to report by adding the corresponding values:
Example:
01
(AC Failure)
+
02
(Low Battery)
+
08
(NSC)
+
16
(RFC)
=
27
.
A failure of any individual or combination of these five programmable supervised conditions will cause the STC
relay to trip. Notice that since LFC is not selected, a Telco line fault will not cause the STC relay to trip and
therefore, no STC trouble report will be sent to the central station by the C/C.
00 = STC Relay Trip Not Used
01 = AC Failure
02 = Low Battery
04 = LFC
08 = NSC
16 = RFC
STC Trip Output Delay for LFC
and/or NSC
Program Location 52
The amount of time (30 or 60 seconds) after a LFC or NSC fault condition occurs that the STC relay will trip.
This trip delay also applies to a LFC or NSC restoral.
CFC Number of Attempts
Program Location 61
The number of attempts that the C/C will try to communicate with the central station over a good Telco line before
Telguard switches the C/C to the cellular path.
0=Disabled
1=2 Attempts
2=4 Attempts
3=8 Attempts
CFC Between Events
Program Location 62
The amount of time that the C/C is allowed to go off-hook, on-hook, then off-hook again to qualify as a
communications failure over Telco.
1=30 Seconds
2=60 Seconds
Standby Battery Size
(standard lead-acid battery)
Program Location 67
The amount of Battery charging current required.
0=No Battery Installed 3=4 Amp/Hour
1=0.8 Amp/Hour 4=7 Amp/Hour
2=1.4 Amp/Hour 5=14 Amp/Hour