Installation Instructions

ManualsBrandsTeltronic ManualsElectronicsRF UNIT P25 BASE STATION RADIO/REPEATER

RF Unit USER AND INSTALLATION MANUAL

01.01.00/1 Rev.1

PRODUCT:

RF Unit

CODE:

D168X01_DDS09

VERSION:

REVISION:

DATE:

16/06/09

CLASSIFICATION:

General information Internal document

DOCUMENT MAINTENANCE

THIS DOCUMENT HAS 17 PAGES

EDIT. DATE AUTHOR DESCRIPTION

1.0 27/12/07 José Roman RF Unit User and Installation Manual.

1.1 09/10/08 Javier Córdova General revision.

1.2 04/11/08 Javier Córdova Correction of subclauses 6.2, 6.3.

1.3 16/06/09 José Román Add FCC RF Exposure Requirements:

DOCUMENT APPROVAL

ACTIVITY NAME DATE SIGNATURE

Prepared

Revised

Project Manager

Approved

R&D Director

Summary of content (16 pages)

PAGE 1
RF Unit USER AND INSTALLATION MANUAL PRODUCT: CODE: RF Unit D168X01_DDS09 VERSION: 01 CLASSIFICATION: REVISION: 03 DATE: General information 16/06/09 Internal document DOCUMENT MAINTENANCE THIS DOCUMENT HAS 17 PAGES EDIT. DATE AUTHOR DESCRIPTION 1.0 27/12/07 José Roman 1.1 09/10/08 Javier Córdova General revision. 1.2 04/11/08 Javier Córdova Correction of subclauses 6.2, 6.3. 1.3 16/06/09 José Román RF Unit User and Installation Manual.
PAGE 2
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 2 of 16 Disclaimer Although every reasonable effort has been made to ensure the accuracy of the information contained herein and any other referred document, this should not be construed as a commitment on the part of Teltronic S.A. Unipersonal, and the liability of Teltronic S.A. Unipersonal for any errors and omissions shall be limited to the correction of such errors and omissions. Teltronic S.A.
PAGE 3
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 3 of 16 CONTENTS: 1. INTRODUCTION......................................................................................................... 4 2. UNPACKING AND CHECKING .................................................................................. 5 3. PREVIOUS CONSIDERATIONS................................................................................. 5 4. INFORMATION ON SAFETY AND ELECTROMAGNETIC COMPATIBILITY ..
PAGE 4
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 4 of 16 1. INTRODUCTION The RF Unit is the RF transceiver of Teltronic P25 systems, with a transmitter output power of 100W. Therefore, this is a mandatory module in the infrastructure P25 network. It is manufactured following a robust mechanical modular design which allows simple and economic maintenance.
PAGE 5
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 5 of 16 2. UNPACKING AND CHECKING The following elements are supplied in the box: RF Unit 50Ω / 20W load termination Power Supply Cable Maintenance Cable Two Ethernet Cables The equipment is supplied with all the modules already assembled in the rack. The modules in the basic configuration are: Power Supply module (RPS), Power Amplifier (RPA P25), Transmitter (RTX P25), Receiver (RRX P25) and Control (RCPU P25).
PAGE 6
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 6 of 16 FCC RF Exposure Requirements: CAUTION: The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is approved with emissions having a source-based time-averaging duty factor not exceeding 50%. Failure to observe these restrictions will result in exceeding the FCC RF exposure limits.
PAGE 7
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 5. EQUIPMENT DESCRIPTION 5.1. FRONT VIEW 1 7 2 3 4 1.- RPS (Repeater Power Supply). 2.- RPA P25 (Repeater Power Amplifier). 3.- RTX P25 (Repeater Transmitter). 4.- RRX P25 (Repeater Receiver). 5.- BSYNC (RF Unit Synchronism) - OPTIONAL 6.- RCPU P25 (Repeater Control Processing Unit). 7.- Power Supply switch. 01.01.00/1 Rev.
PAGE 8
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 5.2. REAR VIEW 17 18 19 20 16 15 14 21 13 22 23 12 24 11 10 9 8.- Power Supply Connector. 9.- TX Antenna Connector (type N). 10.- RF cables between RTX P25 and RPA P25. 11.- RX Antenna Connector (type BNC). 12.- RX Diversity Antenna Connector (not used). 13.- BSYNC Connectors (not used). 14.- Ethernet Connector “ETHERNET_A”. 15.- Ethernet Connector “ETHERNET_B”. 16.- Synchronism Output Connector “SYNC_OUT_2”. 17.
PAGE 9
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 9 of 16 5.3. MODULES 1.- RPS (REPEATER POWER SUPPLY) LEDs to indicate module status. LED TYPE SUPPLY Green NORMAL STATUS On 26.4V Green On 13.2V Green On FUNCTIÓN There are 26.4V at the RPS input There are 26.4V at the RPS output There are 13.2V at the RPS output Power Supply switch (Ref. 7): ON/OFF switch to connect to and disconnect from the RF Unit 2.
PAGE 10
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 10 of 16 4.- RRX P25 (REPEATER RECEIVER) LEDs to indicate module status. ON LED TYPE Green NORMAL STATUS FUNCTIÓN On Power supply correct REF. ERROR Red Off Failure in the 10 MHz reference INT. ERROR Red Off Internal failure BUS ERROR Red Off Communication failure with the RCPU P25 module 5.- SLOT OPTION: BSYNC (RF Unit SYNCHRONISM) LEDs to indicate the status of option BSYNC. LED ON REF.
PAGE 11
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 11 of 16 6.- RCPU P25 (REPEATER CONTROL) LEDs to indicate the module status. LED ON REF. ERROR INT.
PAGE 12
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 12 of 16 6. INSTALLATION GUIDE The following recommendations must be followed closely before starting up the RF Unit module. 6.1. LOCATION The RF Unit has been designed in the standard format of 19” / 3 units high and it must be installed in cabinets with this format. The RF Unit site must be permanent, well-ventilated and without vibrations. 6.2.
PAGE 13
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 13 of 16 6.3. ANTENNA CONNECTION Choose the most adaptable antenna for the installation. The antenna must have an impedance of 50 ohms to the equipment transmission frequency. Install the antenna in accordance with the manufacturer’s instructions. Use a coaxial cable, avoiding as much as possible large cable lengths. Cable impedance is 50 ohms. Measure the ROE of the installation. Never accept a ROE greater than 2.
PAGE 14
RF Unit USER AND INSTALLATION MANUAL Code: D168X01_DDS09 Date: 16/06/09 Page: 14 of 16 7. CONFIGURATION A RF Unit is configured via an NMS (Network Management System). To configure the RF Unit, consult the NMS manual. 8. INCIDENTS The repeater must be repaired by authorized technical personnel only. If a RF Unit failure occurs, the entire RF Unit must be replaced.
PAGE 15
ON OFF REF. ERROR ON INT. ERROR ON BUS ERROR ON RPA P25 ERROR ON RPW ERROR ON ON OFF REF. ERROR ON INT. ERROR ON BUS ERROR ON ON OFF REF. ERROR ON TIME GPS ON BSYNC RRX P25 RTX P25 RF Unit USER AND INSTALLATION MANUAL PPS GPS OFF TIME LOCAL OFF PPS LOCAL OFF 01.01.00/1 Rev.1 Code: D168X01_DDS09 Date: 16/06/09 Page: 15 of 16 INTERNAL POWER SUPPLY FAILURE. CONTACT TECHNICAL SERVICES. Failure in the 10MHz reference. Contact Technical services. Internal failure.
PAGE 16
RF Unit USER AND INSTALLATION MANUAL ON REF ERROR INT ERROR BUS ERROR RCPU DIV ERROR LSC ERROR RF RX ETH LINK1 ETH LINK2 ETH RX ETH TX 01.01.00/1 Rev.1 OFF Code: D168X01_DDS09 Date: 16/06/09 Page: 16 of 16 INTERNAL POWER SUPPLY FAILURE. CONTACT TECHNICAL SERVICES. Failure in the 10MHz reference. Check that the BSYNC module is installed or that the SYNC IN cable is correctly connected. Contact Technical services if still unsolved. ON Internal failure. Contact Technical Services.