FMC130 Advanced LTE terminal with flexible inputs configuration Quick Manual v2.
Warranty ........................................................................................... 16 Table of Contents Warranty Disclaimer .......................................................................... 16 Table of Contents ............................................................................... 2 Know your device ............................................................................... 3 Pinout ...................................................................................
Know your device Figure 1 Device view 3 FMC130 | Wiki
Pinout Table 1 FMC130 2x6 socket pinout PIN NUMBER PIN NAME DESCRIPTION 1 VCC (10-30) V DC (+) Power supply (10-30 V DC). 2 DOUT 3 Digital output, channel 3. Open collector output. Max. 0,5 A DC. 3 DIN 3 / AIN 2 Analog input, channel 2. Input range: 0-30 V DC / Digital input, channel 3. 4 DIN 2-N / AIN 1 Digital input, channel 2, Negative input (ground sense), Analog input, channel 1, Input range: 0-30 VDC. 5 DIN 1 Digital input, channel 1. 6 INPUT 6 TX EXT (LVCAN – TX).
Wiring scheme ^ 1 Figure 3 Wiring scheme 1 Automotive relay 5 FMC130 | Wiki
Set up your device How to insert Micro-SIM card and connect the battery 1. Gently remove FMC130 bottom cover using plastic pry tool from both sides. Then remove the top cover. 2. Insert Micro-SIM card as shown with PIN request disabled or read our Wiki how to enter it later in Teltonika Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot. 3. Connect battery as shown to device. Position the battery in place where it does not obstruct other components. 4.
Setup will continue installing the driver and eventually the PC Connection (Windows) confirmation window will appear. Click Finish to complete the setup. 1. Power-up FMC130 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED Configuration (Windows) indications”. 2. Connect device to computer using Micro-USB cable or Bluetooth connection: • • At first FMC130 device will have default factory settings set.
Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. FMC130 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration, the changes need to be saved to device using Save to device button. Main buttons offer following functionality: Figure 8 Language selection 1. Load from device – loads configuration from device. 2. Save to device – saves configuration to device. 3.
Default configuration settings Quick SMS configuration Movement and ignition detection: Vehicle movement will be detected by accelerometer Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Mounting recommendations • • Connecting wires ▬ Wires should be connected while the module is not plugged in. ▬ Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be ▬ Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available). ▬ Check if power is still available when you turn off any of vehicles devices. kept away from the wires. ▬ There should be no exposed wires.
LED indications Characteristics Basic characteristics Table 5 Basic characteristics Table 3 Navigation LED indications BEHAVIOUR MEANING Permanently switched on GNSS signal is not received Blinking every second Normal mode, GNSS is working Off GNSS is turned off because: Device is not working or Device is in sleep mode Blinking fast constantly Device firmware is being flashed MODULE Name MeiG SLM320-E, MeiG SLM320-LA, Quectel EC21EC, Quectel EC21-AU, Quectel EC21-J, Quectel EC21-KL, Teltonika T
2G bands (EC21) 3G bands (EC21) EC21-EC: GSM: B3/B8 Data support EC21-AU: GSM: B2/B3/B5/B8 POWER EC21-EC: WCDMA: B1/B8 EC21-AU: WCDMA: B1/B2/B5/B8 FMC130-ME1: LTE FDD: B1/B3/B5/B7/B8/B20 LTE-TDD:B38/B40/B41 4G bands (SLM320) Input voltage range 10-30 V DC with overvoltage protection Back-up battery 170 mAh Li-Ion battery 3.7 V (0.
CAN Adapter inputs 1 1-Wire 1 GNSS antenna Internal High Gain Cellular antenna Internal LTE High Gain USB 2.
Electrical characteristics ANALOG INPUT Input voltage (Recommended Operating Conditions), Range 1 Table 6 Electrical characteristics CHARACTERISTIC DESCRIPTION VALUE MIN. TYP. MAX. UNIT SUPPLY VOLTAGE Supply Voltage (Recommended Operating Conditions) +10 +30 V Drain current (Digital Output OFF) 120 µA Drain current (Digital Output ON, Recommended Operating Conditions) 0.1 0.5 A Static Drain-Source resistance (Digital Output ON) 400 600 mΩ kΩ Input resistance (DIN2) 38.
Safety information All wireless data transferring devices produce interference that may affect other devices which are placed nearby. This message contains information on how to operate FMC130 safely. By following these requirements and recommendations, you will avoid The device must be connected only by qualified personnel. dangerous situations.
Warranty Warranty Disclaimer TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE can agree on a different warranty period, for more detailed information please contact our sales manager. LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED.
