Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/CE. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/CE: - EN 60950-1：2006＋A11＋A1＋A12＋A2: 2013 - EN62311 : 2008 - EN 300 328 V1.8.1: 2012 - EN 301 489-1 V1.9.2: 2011 - EN 301 489-17 V2.2.
Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Industry Canada statement: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada.
CPE7000 Indoor LED Indicators Num.
CPE7000 Indoor Connectors: 1. SIM card Slot Cover: Open the cover and insert SIM card into the slot with right direction. 2. Telephone Port (RJ-11): Connect your telephone to Indoor CPE with a RJ-11 telephone cable. 3. LAN Port (RJ-45): Port for connecting PC, hub and switch or other network equipment by RJ-45 Ethernet cable. 4. Reset Button: Press “Reset” button less than 5 seconds to reboot the device. Or press and hold the Reset button 10 seconds to set router to factory default settings. 5.
Installation Please follow the steps below to install the device: Step1: Connect the device LAN port to your PC with a RJ-45 Ethernet cable. Step2: Insert SIM card into the device with right direction. Step3: Insert the power cord into the LTE Indoor CPE's DC-12V power jack; and insert the plug into power outlet. Step4: Switch ON the power. The device will start the booting process. After a few seconds, the LED lights will start blinking.
Easy Setup Please follow the steps below to configure your device through the web interface: Step1: Open the Web browser (Internet Explorer) and enter the default IP address of the IDU CPE : http://192.168.254.251 Step2: Enter IDU administrator login username/password to access the web management interface. The default username/password is admin/admin. Step3: The page displays in your browser after login; you can simply configure the device settings.
Wi-Fi Setting Step1: Select WIFI from main menu. Then screen will display the default setting of SSID, radio channel, working mode, WiFi MAC and SSID broadcast. Step2: Specify a radio channel, working mode, bandwidth in Settings page. Step3: Specify a SSID (Service Set ID), SSID broadcast and Security in Multiple SSID page.
