User's Manual

ManualsBrandsTelrad Networks ManualsElectronicsBreezeCompact 3000 Base Station

Table Of Contents

BreezeCOMPACT

SYSTEM

MANUAL

Release Version: 5.0

August 2014

DN115004

We’re on your wavelength.

Summary of content (99 pages)

PAGE 1
We’re on your wavelength. BreezeCOMPACT SYSTEM MANUAL rRelease Version: 5.
PAGE 2
........................................................
PAGE 3
Legal Rights ........................................................ Legal Rights © Copyright 2015. Telrad Networks Ltd. All rights reserved. The material contained herein is proprietary, privileged, and confidential and owned by Telrad Networks or its third-party licensors. No disclosure thereof shall be made to third parties without the express written permission of Telrad Networks Ltd. Telrad Networks Ltd.
PAGE 4
Legal Rights ........................................................ Disclaimer (a) The Software is sold on an "AS IS" basis. Telrad Networks, its affiliates or its licensors MAKE NO WARRANTIES, WHATSOEVER, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THE SOFTWARE AND THE ACCOMPANYING DOCUMENTATION. TELRAD NETWORKS SPECIFICALLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT WITH RESPECT TO THE SOFTWARE.
PAGE 5
Legal Rights ........................................................ To comply with Industry Canada exposure requirements, and FCC RF exposure requirements in Section 1.1307 and 2.1091 of the FCC Rules, the antenna used for this transmitter must be fixed-mounted on outdoor permanent structures with a separation distance of at least 390 cm from all persons.
PAGE 6
Legal Rights ........................................................ CAUTION: This equipment is designed to permit connection between the earthed conductor of the DC supply circuit and the grounding conductor at the equipment. See installation instructions. ATTENTION: Cet équipement est prévu pour permettre une mise a la terre entre le courant continu et le reste de l’installation. Voir les instructions d’installation.
PAGE 7
Legal Rights ........................................................ Tout personnel impliqué dans l’installation, le fonctionnement et la maintenance de l’installation doivent savoir que les radiations laser sont invisibles. Donc, bien que généralement les protections évitent tout contact direct avec les rayons émis, le personnel doit observer strictement les précautions de sécurité et en particulier, les connecteurs optiques, aussi bien directement ou avec des instruments d’optique.
PAGE 8
Legal Rights ........................................................ Disposal of Electronic and Electrical Waste Disposal of Electronic and Electrical Waste Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product.
PAGE 9
Important Notice ........................................................ Important Notice This manual is delivered subject to the following conditions and restrictions:  This manual contains proprietary information belonging to Telrad Networks Ltd. Such information is supplied solely for the purpose of assisting properly authorized users of the respective Telrad Networks products.
PAGE 10
About This Manual ........................................................ About This Manual This manual describes the BreezeCOMPACT solution, and details how to install, operate and manage the BTS equipment. This manual is intended for technicians responsible for installing, setting and operating the BreezeCOMPACT BTS equipment, and for system administrators responsible for managing the system.
PAGE 11
Contents Contents Chapter 1: System Description ..................................................................................................................16 1.1 1.2 The BreezeCOMPACT Solution................................................................................................................17 1.1.1 The BreezeCOMPACT Family.....................................................................................................17 1.1.2 BreezeCOMPACT Models .................................
PAGE 12
Contents 2.4.5 2.5 Applying the Configuration ..........................................................................................................39 Activating the Unit.....................................................................................................................................40 2.5.1 Creating the BS .............................................................................................................................40 2.5.2 Configuring Radio Cluster Parameters .....
PAGE 13
Contents 3.10 RH Menu....................................................................................................................................................98 3.10.1 General ..........................................................................................................................................98 3.10.2 Ports ..............................................................................................................................................98 3.11 Spectrum Analyzer...
PAGE 14
Figures Figures Figure 1: BreezeCOMPACT Product Topologies 18 Figure 2: Single Sector, Single Carrier 19 Figure 3: Single Sector, Dual Carrier 19 Figure 4: Two Sectors, Two Carriers 20 Figure 5: GPS 21 Figure 6: Telrad Solution 22 Figure 7: Mini-centralized ASN-GW 23 Figure 8: AAA Solution 23 Figure 9: StarSuite NMS Solution 24 Figure 10: GPS Chaining Mode Connectivity 94 Figure 11: Spectrum Analyzer Results 101 BreezeCOMPACT System Manual 14
PAGE 15
Tables Tables Table 1: BreezeCOMPACT Part Numbers, Frequencies and Tx Power 18 Table 2: General Modem and Radio Specifications 25 Table 3: Data Communication (Ethernet Interfaces) 26 Table 4: Configuration and Management 26 Table 5: Standards Compliance, General 26 Table 6: Environmental Specifications 27 Table 7: Mechanical and Electrical Specifications, BreezeCOMPACT1000 Units 27 Table 8: Mechanical and Electrical Specifications, BreezeCOMPACT2000 Units 28 Table 9: Mechanical and Electrical Specification
PAGE 16
Chapter 1: System Description In This Chapter:  “The BreezeCOMPACT Solution” on page 17  “Telrad Overall Solution” on page 22  “Specifications” on page 25
PAGE 17
Chapter 1 - System DescriptionThe BreezeCOMPACT Solution Chapter 1: System Description The BreezeCOMPACT Solution ........................................................ 1.1 The BreezeCOMPACT Solution 1.1.1 The BreezeCOMPACT Family Telrad’s BreezeCOMPACT family of products includes the BreezeCOMPACT base stations, (models 1000, 2000 and 3000.) For more information, please visit the BreezeCOMPACT section of the Telrad website. 1.1.1.1 1.1.1.2 1.1.1.
PAGE 18
Chapter 1 - System DescriptionThe BreezeCOMPACT Solution The BreezeCOMPACT Solution Chapter 1: System Description ........................................................ 1.1.2 BreezeCOMPACT Models Table 1: BreezeCOMPACT Part Numbers, Frequencies and Tx Power Platform Compact1000 P/N 735270 Telrad Part Number (PN) LTE Band CMP.XT-BS-3.4-3.
PAGE 19
Chapter 1 - System DescriptionThe BreezeCOMPACT Solution Chapter 1: System Description The BreezeCOMPACT Solution ........................................................ INFORMATION In the current release, BreezeCOMPACT1000 and 3000 support all three topologies. Note that BreezeCOMPACT2000 supports only the first topology (Single Sector, Single Carrier). The following sections describe each of these topologies. 1.1.3.
PAGE 20
Chapter 1 - System DescriptionThe BreezeCOMPACT Solution Chapter 1: System Description The BreezeCOMPACT Solution ........................................................ Figure 3: Single Sector, Dual Carrier 1.1.3.3 Two Sectors, Two Carriers (One Carrier per Sector) Two BSs support two sectors, each with a bandwidth of 5, 7 or 10 MHz. Each sector is connected to a different 2x2 antenna directed to two sectors.
PAGE 21
Chapter 1 - System DescriptionThe BreezeCOMPACT Solution Chapter 1: System Description The BreezeCOMPACT Solution ........................................................ 1.1.5 GPS GPS is used to synchronize the air link frames of Intra-site and Inter-site located BTSs, in order to ensure that in all Base Stations, the air frame will start at the same time, and that all Base Stations switch from transmit (downlink) to receive (uplink) at the same time.
PAGE 22
Chapter 1 - System DescriptionTelrad Overall Solution Chapter 1: System Description Telrad Overall Solution ........................................................ 1.2 Telrad Overall Solution Figure 6: Telrad Solution 1.2.1 TelCore The TelCore solution is based on MC-ASN-GW for WiMAX and MC-EPC for LTE. TelCore includes a AAA solution for WiMAX and LTE. 1.2.1.
PAGE 23
Chapter 1 - System DescriptionTelrad Overall Solution Chapter 1: System Description Telrad Overall Solution ........................................................ Service components (Service Profiles and Service Flows) are configured in the external ASN-GW. MS authentication and services provisioning are managed by a centralized AAA server, based on user credentials (user name and password). Figure 7: Mini-centralized ASN-GW 1.2.1.
PAGE 24
Chapter 1 - System DescriptionTelrad Overall Solution Chapter 1: System Description Telrad Overall Solution ........................................................ 1.2.
PAGE 25
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ 1.3 Specifications 1.3.
PAGE 26
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ 1.3.2 Data Communication (Ethernet Interfaces) Table 3: Data Communication (Ethernet Interfaces) Item 1.3.3 Description Standard Compliance IEEE 802.
PAGE 27
Chapter 1 - System DescriptionSpecifications Chapter 1: System Description Specifications ........................................................ Table 5: Standards Compliance, General (Continued) Type Radio Standard  ETSI EN 302 326  FCC Part 90 Subpart Z*  IC RSS-192 issue1*  IC RSS-197 issue 3* * In the current release, FCC and IC standards are not applicable for BreezeCOMPACT2000 units. 1.3.
PAGE 28
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ 1.3.6.2 BreezeCOMPACT2000 Table 8: Mechanical and Electrical Specifications, BreezeCOMPACT2000 Units Item 1.3.6.3 Description Dimensions 280 x 510 x 220 mm Weight 19.
PAGE 29
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ Table 10: Attached Antenna 3.3-3.8 DDS 65º (P.N.
PAGE 30
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ 1.3.7.2 3.3-3.8 GHz, 2 Ports 65º Dual Slant (2x2) Table 11: ANT, BS, 3.3-3.8 GHz, DS, Sec.65°, 16.5dBi Minimum (P.N. 300644) Specifications Item 1.3.7.3 Description Frequency Band (MHz) 3,300–3,800 Number of Elements 2 Polarization Linear, +/-45° Gain 16.5dBi +/- 0.5dB VSWR 1.
PAGE 31
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ Table 12: ANT, BS, 3.3–3.8 GHz, DS, Sec.90°, 15.5dBi Minimum (P.N.
PAGE 32
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ 1.3.7.4 3.3-3.8 GHz, 4 Ports 65º Double Dual Slant (4x4) Table 13: ANT-DDP-65°-3.3-3.8 GHz (P.N. 300736) Specifications Item 1.3.7.
PAGE 33
Chapter 1 - System DescriptionSpecifications Specifications Chapter 1: System Description ........................................................ Table 14: ANT-DDP-90°-3.3-3.8 GHz (P.N. 300719) Specifications (Continued) Item 1.3.
PAGE 34
Chapter 2: Commissioning In This Chapter:  “Introduction” on page 35  “BreezeCOMPACT Installation” on page 35  “System Initial Verification” on page 36  “Configuring Parameters Required for Management Connectivity” on page 37  “Activating the Unit” on page 39
PAGE 35
Chapter 2 - CommissioningIntroduction Chapter 2: Commissioning Introduction ........................................................ 2.1 Introduction After completing the installation process, some basic unit's parameters must be configured locally using the Monitor program in order to enable discovery by the Element Management System and remote management of the unit. Refer to “Monitor Program” on page 46 for information about accessing the Monitor program using Telnet and how to use it.
PAGE 36
Chapter 2 - CommissioningSystem Initial Verification Chapter 2: Commissioning System Initial Verification ........................................................ 2.3 System Initial Verification After power-up, the BTS automatically starts a self-testing procedure to verify that:  The BTS has been correctly assembled and installed on site.  All BTS components are functioning properly.  The BTS is ready for commissioning.
PAGE 37
Chapter 2 - CommissioningConfiguring Parameters Required for Management Connectivity Chapter 2: Commissioning Configuring Parameters Required for Management Connectivity ........................................................ 2.
PAGE 38
Chapter 2 - CommissioningConfiguring Parameters Required for Management Connectivity Chapter 2: Commissioning Configuring Parameters Required for Management Connectivity ........................................................  External Management Next Hop Gateway. Must be within the range defined by the External Management IP Address and External Management Subnet Mask. The default is 0.0.0.
PAGE 39
Chapter 2 - CommissioningActivating the Unit Chapter 2: Commissioning Activating the Unit ........................................................ 2 2.4.4.2 At the Manager Number prompt, enter 1 and select the Update option. You are prompted to configure the Community Read Only and the Community Read and Write. Configuring the SNMP Traps Manager By default, the unit is supplied with one SNMP Traps Manager with the following parameters:  IP Address: 192.168.1.
PAGE 40
Chapter 2 - CommissioningActivating the Unit Chapter 2: Commissioning Activating the Unit ........................................................ 4 Define Antenna Associations. After properly completing the steps above, the unit will start operating using default values for all other parameters. Additional parameters should be configured according to Radio Network Planning (RNP) guidelines and other instructions provided by the System Administrator.
PAGE 41
Chapter 2 - CommissioningActivating the Unit Chapter 2: Commissioning Activating the Unit ........................................................ The new BS is added to the list of BSs available in the BS node. 2 Select the BS and configure the following parameters. For some parameters, you may use the default value/option:     2.5.2 In Radio > Basic > General:  Idle Mode Enable: Mark the checkbox to enable Idle Mode. By default, Idle Mode is disabled (not checked).
PAGE 42
Chapter 2 - CommissioningActivating the Unit Chapter 2: Commissioning Activating the Unit ........................................................ 2.5.3 Configuring Antenna Associations Using the Monitor Program 1 2 Select Sector > Antenna Association > Add. You are prompted to configure the following parameters:  RF Port Number: Enter 1.  Antenna Number: Enter the relevant Antenna Number as configured in the Antenna menu.  Antenna Port Number: Enter the relevant Antenna Port Number.
PAGE 43
Chapter 3: Operation and Administration In This Chapter:  “BTS System Management” on page 45  “Monitor Program” on page 46  “IP Address Configuration” on page 49  “Main Menu” on page 50  “BTS Menu” on page 51  “Sector Menu” on page 66  “BS Menu” on page 68  “Chassis Menu” on page 88  “GPS Menu” on page 90  “RH Menu” on page 95  “Spectrum Analyzer” on page 96  “Dual Carrier Load Balancing” on page 99
PAGE 44
Chapter 3 - Operation and AdministrationBTS System Management Chapter 3: Operation and Administration BTS System Management ........................................................ 3.1 BTS System Management The BTS can be managed using any of the following options:  SNMP-based management using StarManager (or another network management system customized to support management of the system).  Using Telnet to access the embedded Monitor application.
PAGE 45
Chapter 3 - Operation and AdministrationMonitor Program Chapter 3: Operation and Administration Monitor Program ........................................................ 3.2 Monitor Program 3.2.1 Accessing the Monitor Program  To access the Monitor program using Telnet: 1 Via the Local Management interface:  Direct local management using the Monitor program can be performed via the Local Management interface. The default local management IP address is 172.31.0.
PAGE 46
Chapter 3 - Operation and AdministrationMonitor Program Chapter 3: Operation and Administration Monitor Program ........................................................ 3.2.2 Using the Monitor Program This section describes the Monitor program structure and navigation rules:  The header of each menu or submenu specifies the unit type, the management IP address, the running software version and the name of the menu/submenu, including the path from the Main menu.
PAGE 47
Chapter 3 - Operation and AdministrationMonitor Program Chapter 3: Operation and Administration Monitor Program ........................................................  If an erroneous value was entered, the reason of the error or help text is displayed and the parameter entry text is displayed again.  If the Monitor program is not used for the period of time defined by the Monitor Inactivity Time-out (see “Monitor Inactivity Timeout” on page 59), the session is terminated automatically.
PAGE 48
Chapter 3 - Operation and AdministrationIP Address Configuration Chapter 3: Operation and Administration IP Address Configuration ........................................................ 3.3 IP Address Configuration 3.3.1 IP Address Configuration Restrictions The following IP addresses should not be used and will be rejected:  0.0.0.0  224.0.0.0 – 255.255.255.255 (Multicasts, RFC 3171 D, RFC 1700 E) 3.3.
PAGE 49
Chapter 3 - Operation and AdministrationMain Menu Chapter 3: Operation and Administration Main Menu ........................................................ 3.
PAGE 50
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5 BTS Menu The BTS menu includes the following options:  General  Connectivity  Unit Control  Management 3.5.1 General The BTS General submenu enables you to view the current values and update the general BTS parameters. The BTS General parameters are:  BTS Number  BTS Name  BTS Address  Contact Person  Legacy ASN-GW Mode 3.5.1.
PAGE 51
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5.1.4 Contact Person An optional descriptive parameter. A string of up to 32 printable characters. The default is null (an empty string). 3.5.1.5 Legacy ASN-GW Mode The Legacy ASN-GW Mode defines functionality supported by the external ASN-GW. Select enable if using a Cisco ASN GW (supports only IP CS services).
PAGE 52
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ The unit supports the following IP connectivity modes:  Out of Band: In the Out-of-Band connectivity mode, different Ethernet ports are used for bearer traffic and external management traffic.  In Band: In the In Band connectivity mode, the sane Ethernet port is used for both bearer traffic and external management traffic.
PAGE 53
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................  Local Management IP Address  Local Management Subnet Mask Note that the permitted value range for certain parameters may depend on the value configured (or to be configured) for the BS Bearer IP Address (see “IP Address” on page 82). Changes in IP Interfaces parameters take effect after the next reset. 3.5.2.2.
PAGE 54
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5.2.2.5 Sector 2 – Default Authenticator IP The IP address of the default authenticator ASN-GW for Sector 2. The default is 0.0.0.0 (must be changed to a valid value). A change in the Default Authenticator takes effect after the next reset. 3.5.2.2.6 External Management IP Address The IP address of the External Management interface.
PAGE 55
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ In Unified Connectivity Mode, the External Management VLAN ID should be configured to the same value as the Bearer VLAN ID. Otherwise, it must differ from the Bearer VLAN ID. A change in the External Management VLAN ID takes effect after the next reset. 3.5.2.2.10 Local Management IP Address The IP address of the Local Management interface.
PAGE 56
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ CAUTION If you want to switch from Data Port 1 to Data Port 2 (or vice versa), the unit must be reset (or powered down and then powered up) after physically connecting to the new port.
PAGE 57
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ For Data Port 1, if the Operational State is Up, the Duplex Mode is forced to Full Duplex. 3.5.2.4 ASN-GW Load Balancing Pools The Load Balancing feature provides a WiMAX operator with the capability to build a resilient ASN infrastructure using ASN-GW redundancy. Every BS is provisioned with two lists of redundant ASN-GWs (pools).
PAGE 58
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5.2.5.2 DSCP The DSCP value of management traffic. The range is 0-63. The default is 0. 3.5.3 Unit Control The Unit Control menu enables various general control functions, such as resetting the BTS, managing the software versions of the BTS and uploading/downloading configuration backup files.
PAGE 59
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ Each software version includes two identifiers:  SW File, which is the name of the downloaded software file. This name does not necessarily include clear identification of the software version number.  SW Version, which provides the software version number.
PAGE 60
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5.3.2.6 Load boot and RCW This option is used to perform an update when the existing BreezeCOMPACT software is upgraded from R4.1 to R5.0. NOTE! For more information about the Boot and RCW upgrades, refer to the software upgrade procedure. 3.5.3.
PAGE 61
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ The Files Control menu includes the following menu options:  Automatic Configuration Backup  Restore From Local File  Current Configuration Files  Create Backup Configuration File 3.5.3.4.1 Automatic Configuration Backup A configuration backup file of the device’s configuration is created automatically every day.
PAGE 62
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ The default TFTP Target IP Address is 192.168.1.1 (the same as the default for the External Management IP Address). 3.5.4 Management The Management menu includes the following options:  SNMP Traps Managers  Authorized Managers 3.5.4.1 SNMP Traps Managers Up to 5 SNMP Traps Managers can be defined.
PAGE 63
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5.4.1.1.4 Enable Traps Distribution Indicates whether the sending of traps to the management station is enabled or disabled. 3.5.4.1.2 Select Use this option to select one of the existing SNMP Traps Managers by its IP address. You can then view the details of the selected Manager, update its parameters (excluding the IP address) or delete it.
PAGE 64
Chapter 3 - Operation and AdministrationBTS Menu Chapter 3: Operation and Administration BTS Menu ........................................................ 3.5.4.2.1.2 Community Read Only The SNMP Read Community to be used by the Authorized Manager. A null Community Read Only means that the read (get) operation can only be performed using the Community Read and Write. Valid Community strings: Up to 10 printable characters, case sensitive. The default is public. 3.5.4.2.1.
PAGE 65
Chapter 3 - Operation and AdministrationSector Menu Chapter 3: Operation and Administration Sector Menu ........................................................ 3.6 Sector Menu In the current release, the unit supports a single sector. The Sector menu includes the following options:  Sector Definition  Radio Cluster  Antenna Association 3.6.1 Sector Definition The Sector Definition menu enables you to view or modify the informational parameters described below. 3.6.1.1 Name The sector name.
PAGE 66
Chapter 3 - Operation and AdministrationSector Menu Chapter 3: Operation and Administration Sector Menu ........................................................ 3.6.2.1 Bandwidth The bandwidth of the Radio Cluster, in MHz. Available valid options are 5 MHz (fiveMHz), 7 MHz (sevenMHz), 10 MHz (tenMHz) & 20MHz (LTE) The default is none. A valid option must be selected. A change in the Bandwidth takes effect after the next reset. 3.6.2.
PAGE 67
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7 BS Menu In the current release, a Single and Dual BS is supported. The BS menu enables you to create the BS, update the BS parameters or delete the BS. The BS ID LSB of an existing BS cannot be modified. To change the BS ID LSB, you must delete the BS and re-create it.
PAGE 68
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.1.4 Name An optional descriptive parameter. A string of up to 32 characters. The default is null. 3.7.1.5 Cell ID The Cell ID (IDCell) used for preamble selection. The range is from 0 to 31. 3.7.1.6 Segment Number The segment (BS) number in a three sector BS (0–2). 3.7.1.7 Preamble Index Read-only. The Preamble Index used by the BS (0–113).
PAGE 69
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2 Select Select the BS to view or update its parameters or to delete it. A BS is selected by its BS Number. The selected BS menu includes the following options:  General  Air Frame Structure  Mobility  Power Control  Feedback  Connectivity  Management Thresholds  Scheduler 3.7.2.
PAGE 70
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2.1.2 Operator ID The unique identifier of the wireless network operator. The same Operator ID must be used by all BSs in the managed wireless network. A number in the range 1–16777215. The Operator ID used in the system is in the format A.B.C, where A, B and C are from 0 to 255.
PAGE 71
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2.2 Air Frame Structure The Air Frame Structure menu includes the following options:  Zones  General  DL Diversity Mode 3.7.2.2.1 Zones The Air Frame Structure - Zones menu includes the following options:  Uplink Data Zone  Downlink Data Zone  First Zone  Uplink Feedback Zone 3.7.2.2.1.
PAGE 72
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ The valid range is from 0 to 69. A change in the UL Permutation Base takes effect after the next reset. 3.7.2.2.1.2 Downlink Data Zone The Downlink Data Zone menu enables you to view/update the values configured for the following parameters:  Basic Rate for Management  Basic Rate for Data  DL Data Permutation Base 3.7.2.2.1.2.
PAGE 73
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................  ctcQamSixtyFourTwoOverThree (64-QAM 2/3)  ctcQamSixtyFourThreeOverFour (64-QAM 3/4)  ctcQamSixtyFourFiveOverSix 64-QAM 5/6 The default is ctcQpskOneOverTwo (QPSK 1/2). A change in the Basic Rate for Data takes effect after the next reset. 3.7.2.2.1.2.3 DL Data Permutation Base The permutation base used in the downlink data zone.
PAGE 74
Chapter 3 - Operation and AdministrationBS Menu BS Menu Chapter 3: Operation and Administration ........................................................ The available options are 2, 4,....34 (2xN, where N=1-17) or -1 for No Limitation. The default is -1 (No Limitation). The Maximum Size cannot be lower than the Minimum Size. A change in the Maximum Size takes effect after the next reset. Table 17 describes the recommended values for the First Zone Minimum Size and Maximum Size:.
PAGE 75
Chapter 3 - Operation and AdministrationBS Menu BS Menu Chapter 3: Operation and Administration ........................................................ Where A=46 for BW of 5 or 10 MHz, and 32 for BW of 7 MHz.
PAGE 76
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................  Total Uplink Duration 3.7.2.2.2.1 Cell ID The Cell ID (IDCell) used for preamble selection. The range is from 0 to 31. A change in the Cell ID takes effect after the next reset. 3.7.2.2.2.2 Preamble Group The preamble group (1 or 2).
PAGE 77
Chapter 3 - Operation and AdministrationBS Menu BS Menu Chapter 3: Operation and Administration ........................................................ The table below describes the DL:UL ratio as a function of BS Bandwidth and Total Uplink Duration. Table 19: DL:UL Ratios BS Bandwidth (MHz) Total Uplink Duration (Slots) 5/10 7 MHz DL:UL Ratio 4 35:12* 5 32:15 6 29:18 3 24:9 4 21:12 * DL:UL Ratio 35:12: Not tested as part of R5.0. 3.7.2.2.
PAGE 78
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2.4.1 Target Ni The target noise and interference level for the PUSC zone, in dBm. The range is from -130 to -110 in steps of 1 (dBm). The default is -127. 3.7.2.4.2 Required C/N Levels Available only in the Show manu. Specifies the required CINR value for different MCSs and feedback zone massages. 3.7.2.4.
PAGE 79
Chapter 3 - Operation and AdministrationBS Menu BS Menu Chapter 3: Operation and Administration ........................................................ 3.7.2.5.4 Ducting Mitigation Mode Sudden changes in the atmosphere's moisture and temperature profiles can on random occasions make radio signals propagate hundreds of kilometers and even more, far beyond the normal radio horizon.
PAGE 80
Chapter 3 - Operation and AdministrationBS Menu BS Menu Chapter 3: Operation and Administration ........................................................
PAGE 81
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................  ASN-GW Load Balancing 3.7.2.6.1 Bearer Interface The Bearer Interface menu enables you to view/update the values configured for the following parameters:  IP Address  Default Gateway Connectivity Status 3.7.2.6.1.1 IP Address The IP address of the bearer interface of the BS. Must be unique in the network.
PAGE 82
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ A change in the 802.1p Priority takes effect after the next reset. 3.7.2.6.3.2 Internal Management Traffic QOS Rules The Internal Management Traffic QOS Rules menu enables you to view/update the values configured for the following parameters:  Diffserv Code Point  802.1p Priority 3.7.2.6.3.2.
PAGE 83
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2.6.3.3.4 Service Flow Data Delivery Type The Service Flow Type for data delivery services: ugs, rtvr, nrtvr, be, ertvr or any. A change in the Service Flow Data Delivery Type takes effect after the next reset. 3.7.2.6.3.3.5 Service Flow Traffic Priority The priority of Service Flow traffic. The value can be 0–7 or ANY (255).
PAGE 84
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2.6.4.1 Pools Availability The Pools Availability option enables you to view/update the status (Enabled/Disabled) of each of the pools. The Secondary Pool can be enabled only if the Primary Pool is enabled. A change in the Pool Availability takes effect after the next reset. 3.7.2.6.4.
PAGE 85
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ 3.7.2.8 Scheduler Scheduling uncommitted (above the maximum reserved rate) traffic can be done using one of the following options:  Equal Time (ET) scheduling mode, in which air resources are scheduled in a fair manner that is proportional to the users' excess traffic (maximum sustained rate - maximum reserved rate) SLAs.
PAGE 86
Chapter 3 - Operation and AdministrationBS Menu Chapter 3: Operation and Administration BS Menu ........................................................ A change in the Scheduler Mode takes effect after the next reset. 3.7.2.8.
PAGE 87
Chapter 3 - Operation and AdministrationChassis Menu Chapter 3: Operation and Administration Chassis Menu ........................................................ 3.8 Chassis Menu The Chassis menu includes the following options:  General  Ports Control 3.8.1 General The Chassis General menu enables you to view the following read-only general chassis properties and status:  HW Version.  Serial Number.  Temperature (°C).  Operational SW Version.  Shadow SW Version.
PAGE 88
Chapter 3 - Operation and AdministrationChassis Menu Chapter 3: Operation and Administration Chassis Menu ........................................................ 3.8.1.2 Maximal Frame Size The maximal size (excluding the preamble) of frames on the Ethernet port. The range is from 1,400 to 1,600 Bytes. The default is 1,578 Bytes. A change in the Maximal Frame Size takes effect after the next reset. NOTE! Relevant when the Legacy ASN is enabled. 3.8.
PAGE 89
Chapter 3 - Operation and AdministrationGPS Menu Chapter 3: Operation and Administration GPS Menu ........................................................ 3.9 GPS Menu The GPS menu includes the following options:  General Configuration  Inventory & Statuses 3.9.1 General Configuration The GPS General Configuration menu enables you to view/update the parameters described below. 3.9.1.1 GPS Type The type of time synchronization source to be used.
PAGE 90
Chapter 3 - Operation and AdministrationGPS Menu Chapter 3: Operation and Administration GPS Menu ........................................................ 3.9.1.5 UTC Time and Date The UTC (Coordinated Universal Time) date and time. This parameter is only configurable if the GPS Type is set to None. Otherwise, it is the read-only data received from the GPS receiver.
PAGE 91
Chapter 3 - Operation and AdministrationGPS Menu Chapter 3: Operation and Administration GPS Menu ........................................................ 3.9.1.8 Stop TX After Hold Over Timeout This parameter applies only when the External 1 PPS is enabled. It indicates whether the BTS should stop data transmission if the unit does not receive an external 1 PPS signal and the holdover passed timeout has occurred.
PAGE 92
Chapter 3 - Operation and AdministrationGPS Menu Chapter 3: Operation and Administration GPS Menu ........................................................ 3.9.1.14 Stop Date When Daylight Saving is enabled, this parameter defines the date for ending the daylight-savings feature (Advance Hour Factor hours after midnight at the end of this day). Use the format dd.mm to define the date and month at which to end activating the daylight-savings feature.
PAGE 93
Chapter 3 - Operation and AdministrationGPS Menu Chapter 3: Operation and Administration GPS Menu ........................................................ 3.9.2.8 Hold Over timeout passed This parameter indicates whether the Hold Over Timeout has passed (applies only after entering Hold Over state). 3.9.2.9 BS Stopped to Transmit This parameter indicates whether the BSs stopped transmitting due to being in Hold Over state for a period longer than the Hold Over Timeout. 3.9.2.
PAGE 94
Chapter 3 - Operation and AdministrationRH Menu Chapter 3: Operation and Administration RH Menu ........................................................ 3.10 RH Menu The RH (Radio Head) menu includes the following options:  General  Ports 3.10.
PAGE 95
Chapter 3 - Operation and AdministrationSpectrum Analyzer Chapter 3: Operation and Administration Spectrum Analyzer ........................................................ Calculated Tx Power equals the Radio Cluster’s Tx Power. 3.10.2.2 RH Status Mask This parameter is read-only. This parameter is a decimal number representing the value of a 32-bit mask (bits 0–31) indicating possible failures. This parameter applies only for an installed and associated RH. For a No Failure status, the value is 0.
PAGE 96
Chapter 3 - Operation and AdministrationSpectrum Analyzer Chapter 3: Operation and Administration Spectrum Analyzer ........................................................ 8 – Set Default Configuration 3.11.3 Show Current State This parameter displays the Spectrum Analyzer state per BS/Sector. It indicates the enabled/disabled state and scanning state. 3.11.4 Start Scanning This parameter starts the scanning process. 3.11.5 Abort Scanning This parameter aborts the scanning state.
PAGE 97
Chapter 3 - Operation and AdministrationSpectrum Analyzer Chapter 3: Operation and Administration Spectrum Analyzer ........................................................ 3.11.6 Show Results This parameter shows the sort method to be used for displaying results. Select 0 for by Freq or 1 for by NI level. The following figure shows a results example for the Spectrum Analyzer.
PAGE 98
Chapter 3 - Operation and AdministrationDual Carrier Load Balancing Chapter 3: Operation and Administration Dual Carrier Load Balancing ........................................................ 3.12 Dual Carrier Load Balancing BreezeCOMPACT’s Dual Carrier topology in a Single Sector enables load balancing between two carriers. The load is distributed between the two carriers using a load balancing algorithm in each carrier.
PAGE 99
........................................................ We’re on your wavelength.