User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. CHOOSING THE INSTALLATION LOCATION
- 3. INSTALLATION
- 3.1 Connections and LED Indications
- 3.2 Inserting the Battery
- 3.3 PowerManage 360 Connections
- 3.4 GSM Connection and Configuration
- 3.5 SIM Card Insertion
- 3.6 PowerMaster 360 Prerequisites
- 3.7 Enrolling / Deleting a Z-Wave Device
- 1. Press and hold the (+) button (“J” in Figure 3.1) for 2 seconds. The red LED (“N” in Figure 3.1) blinks slowly.
- To delete an enrolled device, proceed as follows.
- 1. Press and hold the (-) button (“J” in Figure 3.1) for 2 seconds. The red LED (“N” in Figure 3.1) blinks quickly and a happy beep is heard and then the LED turns off.
- 3.8 Panel Reset
- 3.9 Factory Default Restore
- 4. PROGRAMMING
- 4.1 General Guidance
- 4.2 Entering the "Installer Mode" and Selecting a Menu Option
- 4.3 Setting Installer Codes
- 4.4 Zones / Devices
- 4.4.1 General Guidance & Zones/Devices Menu Options
- 4.4.2 Adding New Wireless Devices
- 4.4.3 Deleting a Device
- 4.4.4 Modifying or Reviewing a Device
- 4.4.5 Replacing a Device
- 4.4.6 Configuring Soak Test Mode
- 4.4.7 Defining Configuration Defaults for "Device Settings"
- 4.4.8 Updating Devices after Exiting Installer Mode
- 4.5 Control Panel
- 4.5.1 General Guidance – "Control Panel" Flow-Chart & Menu Options
- 4.5.2 Configuring Arming/Disarming and Exit/Entry Procedures
- 4.5.3 Configuring Zones Functionality
- 4.5.4 Configuring Alarms & Troubles
- 4.5.5 Configuring Sirens Functionality
- 4.5.6 Configuring Audible & Visual User Interface
- 4.5.7 Configuring Jamming and Supervision (Missing device)
- 4.5.8 Configuring Miscellaneous Features
- 4.6 Communication
- 4.6.1 General Guidance – "Communication" Flow-Chart & Menu Options
- 4.6.2 Configuring GSM-GPRS (IP) - SMS Cellular Connection
- 4.6.3 Configuring Events Reporting to Monitoring Stations
- 4.6.4 Configuring Events Reporting to Private Users
- 4.6.5 Configuring Motion Cameras for Visual Alarm Verification
- 4.6.6 Configuring Upload / Download Remote Programming Access Permission
- 4.6.7 Broadband2F
- 4.7 Custom Names
- 4.8 Diagnostics
- 4.9 User Settings
- 4.10 Factory Default
- 4.11 Serial Number
- 4.12 Partitioning
- 4.13 Operation Mode
- 5. PERIODIC TEST
- 6. MAINTENANCE
- 7. READING THE EVENT LOG
- APPENDIX A. PowerMaster 360 Configurator
- APPENDIX B. VISONIConfig Mobile Installer App. For PowerMaster 360
- APPENDIX C. User Mobile Application with PowerMaster 360
- APPENDIX D. Specifications
- APPENDIX E. Working with Partitions
- APPENDIX F. Detector Deployment & Transmitter Assignments
- APPENDIX G. Event Codes
- APPENDIX H. Sabbath Mode
- APPENDIX I. Glossary
- APPENDIX J. Compliance with Standards
- PowerMaster 360 Quick User Guide
4. PROGRAMMING
D-305735 PowerMaster 360 Installer's Guide 31
4.6 Communication
4.6.1 General Guidance – "Communication" Flow-Chart & Menu Options
The COMMUNICATION menu enables you to configure and customize the communication and reporting of alarm,
troubles and other system events for monitoring companies or private users according to your local requirements and
personal preferences. PowerMaster 360 offers a variety of communication means including Cellular GSM, GPRS,
EMAIL, MMS or SMS and IP via broadband internet connection.
The "04.COMMUNICATION" menu contains several sub-menu options, each covering a group of configurable features
and parameters related to the communication and reporting as follows (see detailed list in Step 3 of the chart below):
Option
Description of Option Features and Parameters
Section
2:GSM/GPRS/SMS
Contains configurable features and parameters related to the Cellular connection
of the PowerMaster 360 system.
4.6.2
3:C.S. REPORTING
Contains configurable features and parameters related to Reporting of event
messages to Monitoring Stations via cellular or IP broadband communication.
4.6.3
4:PRIVATE REPORT
Contains configurable features and parameters related to Reporting event
messages to Private Users via email, MMS or SMS.
4.6.4
5:MOTION CAMERA
Contains configurable features and parameters related to Motion Cameras for
Video Alarm Verification.
4.6.5
6:UP/DOWNLOAD
Contains configurable connection information, access permission and security
codes related to the Upload/Download procedures via GPRS.
4.6.6
7:BROADBAND
1
Contains DHCP Client settings, enables to enter LAN parameters, to reset
broadband module and to enter LAN parameters.
4.6.7
To enter the "04.COMMUNICATION" menu and to select and configure an option, proceed as follows:
Step 1
Step 2
Step 3
Step 4
Select "COMMUNICATION" Select Communication
Sub-menu option
Select the "Communication" Parameter you wish to configure
See
INSTALLER MODE
04.COMMUNICATION
2:GSM/GPRS/SMS
GPRS PASSWORD
4.6.2
SMS REPORT
NETWORK ROAMING
GPRS APN
GPRS ALWAYS ON
GPRS USERNAME
GSM KEEP ALIVE
SIM PIN CODE
TRANS. PROTOCOL
3:C.S. REPORTING
01:REPORT EVENTS
4.6.3
02:1st RPRT CHAN
47:GSM RETRIES
() These options
are available only to
the "Master Installer"
05:DUAL REPORT
48:BB IP RETRIES
11:RCVR1 ACCOUNT
51: AUTO-TST LOOP
12:RCVR2 ACCOUNT
52:AUTO-TST TIME
21:IP RCVR 1
53:COM.FAIL RPRT
22:IP RCVR 2
→GSM/GPRS FAIL
26:SMS RCVR 1
61:RPRT CNF ALRM
27:SMS RCVR 2
62:RECENT CLOSE
63:ZONE RESTORE
64:SYST.INACTIVE
66:24H ZONE RPRT
4:PRIVATE REPORT
SMS REPORT
EMAIL BY SERVER
4.6.4
→REPORTED EVENTS
→1st E-MAIL
See also
User's
Guide
Chap. 4
Section
B.12
→1st SMS tel#
→2nd E-MAIL
→2nd SMS tel#
→3rd E-MAIL
→3rd SMS tel#
→4th E-MAIL
→4th SMS tel#
SMS/MMS BY SRVR
1
The name of the product is PowerLink3 IP Communicator