User's Manual
Table Of Contents
- 1 Introduction
- 2 M.2 Overview
- 3 M.2 Module Interface Details
- 3.1 USB 2.0 High-Speed – IPC Interface
- 3.2 (U)SIM Interface
- 3.3 GNSS Interface
- 3.4 System Control Interface
- 3.5 Tunable Antenna Control Interface
- 3.6 In-Device Coexistence Interface
- 3.7 Power Supply Interface
- 3.8 Trace & Debug Interface
- 3.9 Configuration Pins
- 3.10 Reserved Pins
- 3.11 No Connect Pins
- 3.12 Antenna Interface
- 4 Development Tools
- 5 Windows Software Components
- 6 Modem Configuration on Linux Based PC
- 7 Operating Environment
- 8 Power Delivery Requirements
- 9 Other Information
- 10 WWAN Card Type 3042-S3-B
- 11 Safety Recommendations
- 12 Conformity assessment issues
- 13 FCC/IC Regulatory notices
- 14 Document History
xN930 M.2 Hardware User Guide
1VV0301078 Rev.6 – 2013-11-12
39
GND
P
Ground
-
40
I2C_SCL
IO
I2C Clock – GNSS Support
1.8 V
41
N/C
-
Not connected internally on M.2
-
42
I2C_SDA
IO
I2C Data – GNSS Support
1.8 V
43
N/C
-
Not connected internally on M.2
44
I2C_IRQ
I
GNSS Interrupt Request – GNSS
Support
1.8 V
45
GND
P
Ground
-
46
SYSCLK
O
26 MHz reference Clock output for
external GNSS
module
1.8 V
47
N/C
-
Not connected internally on M.2
-
48
TX_BLANKING
O
GNSS Blanking Signal used to
indicate 2G Tx burst.
1.8 V
49
N/C
-
Not connected internally on M.2
-
50
N/C
-
Not connected internally on M.2
-
51
GND
P
Ground
-
52
N/C
-
Not connected internally on M.2
-
53
N/C
-
Not connected internally on M.2
-
54
N/C
-
Not connected internally on M.2
-
55
N/C
-
Not connected internally on M.2
-
56
N/C
-
Not connected internally on M.2
-
57
GND
P
Ground
-
58
N/C
-
Not connected internally on M.2
-
59
ANTCTL0
I
RF Antenna Tuning Control Signal
0
1.7 V -
2.6 V
60
COEX0
-
Wireless Coexistence between
WWAN and WiFi/BT
modules
-
61
ANTCTL1
I
RF Antenna Tuning Control Signal
1
1.7 V -
2.6 V
62
COEX1
-
Wireless Coexistence between
WWAN and WiFi/BT
modules
-
63
ANTCTL2
I
RF Antenna Tuning Control Signal
2
1.7 V -
2.6 V
64
COEX2
Wireless Coexistence between
WWAN and WiFi/BT
modules
-
Pin
Signal Name
I/O
Description
Supply
65
ANTCTL3
I
RF Antenna Tuning Control Signal
3
1.7 V -
2.6 V
66
SIM DETECT
I
SIM Card Detection (I) (low
active).
• Pull-up resistor on WWAN M.2
module
1.8 V
67
RESET#
I
Single control to reset WWAN (O)
(*not used on ULTRABOOK
designs)
1.8 V
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 24 of 77