User's Manual
Table Of Contents
- GC864 Hardware User Guide
- APPLICABILITY TABLE
- 1. Introduction
- 2. Overview
- 3. GC864 Mechanical Dimensions
- 4. GC864-QUAD/PY Module Connections
- 5. Hardware Commands
- 6. Power Supply
- 7. Antenna
- 8. Logic Level Specifications
- 9. Serial Ports
- 10. Audio Section Overview
- 11. General Purpose I/O
- 11.1. GPIO Logic Levels
- 11.2. Using a GPIO Pad as INPUT
- 11.3. Using a GPIO Pad as OUTPUT
- 11.4. Using the RF Transmission Control GPIO4
- 11.5. Using the RFTXMON Output GPIO5
- 11.6. Using the Alarm Output GPIO6
- 11.7. Using the Buzzer Output GPIO7
- 11.8. Magnetic Buzzer Concepts
- 11.9. Using the Temperature Monitor Function
- 11.10. Indication of Network Service Availability
- 11.11. RTC Bypass Out
- 11.12. VAUX1 Power Output
- 12. DAC and ADC Section
- 13. Mounting the GC864-QUAD/PY on the Board
- 14. Packing System
- Conformity Assessment Issues
GC864 Hardware User Guide
1vv0300733 Rev.12 – 2009-06-04
Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved. Page 15 of 69
Pin Signal I/O Function
Internal
Pull up
Type
25 C103/TXD I Serial data input (TXD) from DTE CMOS 2.8V
26 C104/RXD O Serial data output to DTE CMOS 2.8V
27 C107/DSR O
Output for Data set ready signal (DSR) to DTE/ DVI1_RX (Digital Voice
Interface)
CMOS 2.8V
28 C106/CTS O Output for Clear to send signal (CTS) to DTE CMOS 2.8V
29 C108/DTR I Input for Data terminal ready signal (DTR) from DTE CMOS 2.8V
30 C125/RING O Output for Ring indicator signal (RI) to DTE CMOS 2.8V
31 C105/RTS I Input for Request to send signal (RTS) from DTE CMOS 2.8V
32 C109/DCD O Output for Data carrier detect signal (DCD) to DTE CMOS 2.8V
DAC and ADC
37 ADC_IN1 AI Analog/Digital converter input A/D
38 ADC_IN2 AI Analog/Digital converter input A/D
39 ADC_IN3 AI Analog/Digital converter input A/D
40 DAC_OUT AO Digital/Analog converter output D/A
Miscellaneous Functions
45 STAT_LED O Status indicator led CMOS 1.8V
46 GND - Ground Ground
49 PWRMON O Power ON Monitor CMOS 2.8V
50 VAUX1 - Power output for external accessories -
51 CHARGE AI Charger input Power
52 CHARGE AI Charger input Power
53 ON/OFF* I
Input command for switching power ON or OFF (toggle command). The
pulse to be sent to the GC864-QUAD/PY must be equal or greater than
1 second.
47K
Ω
Pull up to VBATT
54 RESET* I Reset input
55 VRTC AO VRTC Backup capacitor Power
36 DVI2_CLK - Digital Voice Interface Clock 4.7K
Ω
CMOS 2.8V
Telit GPIO
56 TGPIO_19 I/O Telit GPIO19 Configurable GPIO CMOS 2.8V
57 TGPIO_11 I/O Telit GPIO11 Configurable GPIO CMOS 2.8V
58 TGPIO_20 I/O Telit GPIO20 Configurable GPIO CMOS 2.8V
59 TGPIO_04 I/O Telit GPIO4 Configurable GPIO / RF Transmission Control CMOS 2.8V
60 TGPIO_14 I/O Telit GPIO14 Configurable GPIO CMOS 2.8V
61 TGPIO_15 I/O Telit GPIO15 Configurable GPIO CMOS 2.8V
62 TGPIO_12 I/O Telit GPIO12 Configurable GPIO CMOS 2.8V
63 TGPIO_10 I/O Telit GPIO10 Configurable GPIO / DVI2_TX (Digital Voice Interface) CMOS 2.8V
64 TGPIO_22 I/O Telit GPIO22 Configurable GPIO CMOS 1.8V
65 TGPIO_18 I/O Telit GPIO18 Configurable GPIO / DVI2_RX (Digital Voice Interface) CMOS 2.8V
66 TGPIO_03 I/O Telit GPIO3 Configurable GPIO CMOS 2.8V
67 TGPIO_08 I/O Telit GPIO8 Configurable GPIO CMOS 2.8V