N/DYM SERIES WIRELESS USER GUIDE GEBRAUCHSANWEISUNG MODE D’EMPLOI INSTRUCCIONES DEL USUARIO WIRELESS MICROPHONE S Y S T E M D R A H T - SYSTEME DE SISTEMA L MICROPHONE MICRÓFONO S A N S INALÁMBRICO O S E S MIKROFONS Y S T E M F I L DE
ENGLISH Table of Contents 1. Quick System setup guide 2. System Description 3. Detailed system/component setup instructions 3.1 Receiver Setup & Operation 3.2 Handheld Transmitter Setup 3.3 Beltpack Setup 4. Guidelines/Recommendations for best performance 5. Troubleshooting Guide 6. Technical Specifications 7. Certifications 8. Components & Accessories 9. Service/Warranty 1. Quick System Setup Guide Receiver Setup 1.
ENGLISH 2. System Description The Electro-Voice N/DYM Wireless is a series of 10 channel frequency agile UHF wireless systems that combine EV’s legendary quality and reliability with high value. The N/DYM Series transmitters and receivers operate in the UHF frequency range on one of ten channels between 800 and 814 MHz. The well-designed audio circuitry ensures excellent signal-to-noise ratio with accurate sound quality. System Features • 10 Channel Frequency Agile UHF system operation.
ENGLISH Figure 1. Front View Figure 2. Rear View 5. Channel change lock-out. Once the channel has been set on the receiver, the N/DYM system has the capability to deactivate or lock-out the channel change button. This is done by depressing the set button for 10 seconds or more. Lock-out is active when the decimal point illuminates in the lower right corner of the channel display. This will defeat the set button. To override or defeat the lockout function, again depress the set button for 10 seconds.
ENGLISH 3.2 Handheld Transmitter Setup 1. Insert battery. Slide open the hinged battery compartment cover by placing your thumb on the indents of the battery door (at the bottom of the transmitter) and gently pushing down (see Figure 3). Insert the battery, terminal end first, into the compartment, with the smaller positive terminal to the right. Figure 3. 5. Unmute the audio by sliding the audio switch (immediately below the mic element) towards the windscreen.
ENGLISH 3.3 Bodypack Transmitter Setup 1. Insert battery. Open the hinged battery compartment by placing your thumb or finger on the indent labeled OPEN on the battery door and pushing down, see Figure 6. When inserting the battery, pay attention to the polarity (+/-) and insert the terminals into the battery compartment first. Close the battery door by sliding the door shut. 5. Connect the audio source.
ENGLISH Figure 6. 4 Guidelines/Recommendations for best performance Compatibility The receiver and transmitter must be set to the same channel to operate together. Using Multiple Wireless Systems If two or more N/DYM Wireless and/or other VHF/UHF wireless systems are being used in the same location, proper frequency coordination is necessary to avoid interference.
ENGLISH 5 Troubleshooting Guide Problem Possible Causes Solutions No audio & no lights on receiver Receiver is off Make sure that power supply is properly connected and providing power to the receiver. No audio & no Tx ON light on receiver Transmitter is off. Turn on transmitter power switch. No ( or dead ) battery in transmitter. Insert fresh battery in transmitter. Faulty battery contacts in transmitter. Clean contacts. Transmitter audio switch is off (signal is muted).
ENGLISH 6 N/DYM Wireless Series System Technical Specifications UHF Receivers: NRU and NRU-G Receivers Receiver Type Synthesized PLL Frequency Range (RF) Between 800 - 814 MHz Number of Selectable Channels 10 Diversity True Diversity with Secure-PhaseTM RF Sensitivity < .8 uV for 12 dB SINAD FCC Data Approved under part 15 Audio Output, Frequency Response 50 – 15 kHz +/- 2 dB Audio Output, Balanced (XLR) -20 dBV (600 Ohm Load) Audio Output, Unbalanced (1/4") adjustable 8 mv to 0.
ENGLISH 7 Certifications CERTIFICATIONS NRU, NRSCU, Certified to ETS 300 445, Conforms to European Union directives, eligible to bear CE marking. NHTU, NBPU, Certified to I-ETS 300 442 and ETS 300 445, Conforms to European Union directives, eligible to bear CE marking. Licensing of Electro-Voice equipment is the user’s responsibility and license eligibility depends on the user’s classification, and frequency selected.
ENGLISH 9. Service/Warranty Factory Service If factory service is required, ship the unit prepaid in its original carton to: Telex EVI Audio GmbH Hirschberger Ring 45 D-94315 Straubing Telephone: +49 (0) 9421 706 0 Fax: +49 (0) 9421 706 350 Enclose a note describing the problem along with any other pertinent information.
ENGLISH Service/Warranty – North America Factory Service If factory service is required, ship the unit prepaid in its original carton to: EV Audio Service c/o Telex Communications 8601 E. Cornhusker Highway Tel: 402/467-5321 Fax: 402/467-3279 Enclose a note describing the problem along with any other pertinent information.
R Telex Communications Inc., 12000 Portland Ave. South Burnsville, MN 55337, USA 800/328-3771, 952/884-4051, Fax: 952/884-0043 MANUAL - N/DYM Series Wireless © Telex Communications, Inc. 2000 ♦ Litho in U.S.A.
