Datasheet

14
SPECIFICATIONS
WaveSurfer 4024HD WaveSurfer 4034HD WaveSurfer 4054HD WaveSurfer 4104HD
Triggering System
Modes Normal, Auto, Single, and Stop
Sources Any input channel, Ext, Ext/5, or Line; slope and level unique to each source (except Line trigger)
Coupling DC, AC, HFRej, LFRej
Hold-off From 10 ns up to 20 s or from 1 to 100,000,000 events
Pre-trigger Delay 0 to 100% of full scale
Post-trigger Delay 0 to 10,000 divisions
Internal Trigger Level Range ±4.1 div from center (typical)
External Trigger Level Range Ext (±0.610 mV); Ext/5 (±3.05 V)
Maximum Trigger Rate 175,000 waveforms/second
Trigger Sensitivity with Edge Trigger
(Ch 1–4)
0.9 division @ 10 MHz 0.9 division @ 10 MHz
1.0 divisions @ 200 MHz
0.9 division @ 10 MHz
1.0 divisions @ 200 MHz
0.9 division @ 10 MHz
1.0 divisions @ 200 MHz
Trigger Types Edge, Width, Logic (Pattern), TV (NTSC, PAL, SECAM, HDTV - 720p, 1080i, 1080p), Runt, Slew Rate,
Interval (Signal or Pattern), Dropout, Qualied (State or Edge). External input supports Edge trigger only.
Low Speed Serial Protocol Triggering (Optional)
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay
Measure, Zoom, and Math Tools
Measurement Parameters Up to 6 parameters can be calculated at one time on any waveforms, selected from the following list of
measurements: Amplitude, Area, Base, Delay, Duty Cycle, Fall Time (90%–10%), Fall Time (80%–20%), Frequency,
Maximum, Mean, Minimum, Overshoot+, Overshoot-, Peak-Peak, Period, Phase, Rise Time (10%–90%), Rise
Time (20%–80%), RMS, Skew, Standard Deviation, Top, Width+, Width-. Statistics and histicons can be added to
measurements. Measurements can be gated.
Zooming Use front panel QuickZoom button, or Rectangle-Zoom using touch screen or mouse.
Math Functions Up to 2 math functions can be calculated at one time on any waveforms, selected from the following list of
operations: Sum, Difference, Product, Ratio, Absolute Value, Average, Derivative, Enhanced Resolution, Envelope,
Floor, Integral, Invert, Reciprocal, Rescale, Roof, SinX/x, Square, Square Root, Trend, Zoom and FFT (with Power
Spectrum output; Rectangular, VonHann and FlatTop windows).
Display System
Size 12.1" widescreen capacitive touch screen
Resolution 1280 x 800 pixels
Probes
Standard Probes PP019 (5 mm),
1 per channel
PP026 (5 mm),
1 per channel
Probing System BNC and Teledyne LeCroy ProBus for active voltage, current, and differential probes
Connectivity
Ethernet Port 1 x 10/100BaseT Ethernet interface (RJ45 port)
Removable Storage 1 Micro SD port, 16 GB Micro SD card installed standard
USB Host Ports 2 front USB 3.1 Gen1 ports, 2 back USB 2.0 ports
USB Device Port 1 USBTMC over USB 2.0 port
External Monitor Port 1 HDMI port, supports up to 1280 x 800 pixels
Remote Control Microsoft COM Automation or LeCroy Remote Command Set
Network Communication Standard VICP or VXI-11, LXI compatible
Power Requirements
Voltage 100 to 240 VAC ±10% @ 50 to 60 Hz ±10%; 100 to 120 VAC ±10% @ 400 Hz ±5%; automatic AC voltage selection
Nominal Power Consumption 90 W / 90 VA
Max Power Consumption 150 W / 150 VA
Environmental
Temperature Operating: 0 °C to +50 °C; Non-operating: –30 °C to +70 °C
Humidity Operating: 5% to 90% RH (non-condensing) at ≤30 °C, upper limit derates to 50% RH (non-condensing) at +50 °C;
Non-operating: 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude Operating: 3,048 m (10,000 ft) max at ≤ 25 °C; Non-operating: up to 12,192 meters (40,000 ft)
Size and Weight
Dimensions (HWD) 10.7” H x 14.9” W x 6.3” D (273 mm x 380 mm x 160 mm)
Weight 11.7 lbs (5.3 kg)
Certifications
CE Certication
UL and cUL Listing
CE compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition), and
CAN/CSA C22.2 No. 61010-1-12
Warranty and Service
3-year warranty; calibration recommended annually. Optional service programs include extended warranty,
upgrades, and calibration services.